Chamberlain Group Inc The 1619 Manuel D’Utilisation
CHAMBERLAIN, SEARS, LIFTMASTER,
MASTER MECHANIC, DO IT - SECTIONS 1, 2 AND 3
MASTER MECHANIC, DO IT - SECTIONS 1, 2 AND 3
Determine if your system has code switches or a smart-learn button. If your
system has code switches they can be found in an original hand held remote or
on the motor unit receiver. The receiver can be mounted on the side or back
panel of the motor unit or could be mounted on the ceiling or wall (locate the
small gray wire antenna). If you have code switches proceed to Section 1.
system has code switches they can be found in an original hand held remote or
on the motor unit receiver. The receiver can be mounted on the side or back
panel of the motor unit or could be mounted on the ceiling or wall (locate the
small gray wire antenna). If you have code switches proceed to Section 1.
Note: Systems that have a yellow, white, or gray smart-learn button will have
code switches in the original hand held remote. You must have the original
hand held remote to complete this section.
code switches in the original hand held remote. You must have the original
hand held remote to complete this section.
If your hand held remotes do not contain code switches, your system will have a
green or orange smart-learn button. Proceed to Section 2 and 3.
green or orange smart-learn button. Proceed to Section 2 and 3.
1 CODE SWITCH SYSTEMS
If the switch is in the plus (+) position place a 1, neutral (0) position place a 2,
negative (-) position place a 3 in the corresponding box in the TABLE below.
negative (-) position place a 3 in the corresponding box in the TABLE below.
Exception: If your original hand held remote has 3 buttons and you are using the
small button on left, place a 1; center button, place a 2; large button place a 3 in
box 1 in the table above. Boxes 2 through 9, place number that corresponds with
switch position.
small button on left, place a 1; center button, place a 2; large button place a 3 in
box 1 in the table above. Boxes 2 through 9, place number that corresponds with
switch position.
Choose a 4-digit Personal Identification Number (PIN). Any combination of
numbers from 0 to 9 may be used.
numbers from 0 to 9 may be used.
Write PIN here:
To test, enter PIN followed by any 5th additional number.
Note: Do not use the * star or # pound keys as a 5th number.
Note: Do not use the * star or # pound keys as a 5th number.
If programming is unsuccessful, Check to be sure the code from TABLE above
match’s switch positions from your system. Clear and start over.
match’s switch positions from your system. Clear and start over.
CLICKER MODEL CLK1
Wireless Keypad - For use with Garage Door Openers
THE CLICKER IS NOT COMPATIBLE WITH SOME ROTATING CODE SYSTEMS
SUCH AS GENIE INTELLICODE OR STANLEY SECURE CODE GARAGE DOOR
OPENER SYSTEMS DEVELOPED BY SEVERAL MANUFACTURERS SINCE 1996.
SUCH AS GENIE INTELLICODE OR STANLEY SECURE CODE GARAGE DOOR
OPENER SYSTEMS DEVELOPED BY SEVERAL MANUFACTURERS SINCE 1996.
NOTICE: To comply with FCC and or Industry Canada rules, adjustment or modifications of this receiver
and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE
NO OTHER USER SERVICEABLE PARTS.
and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE
NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
WARNING
CAUTION
WARNING
WARNING
ATTENTION
AVERTISSEMENT
AVERTISSEMENT
AVERTISSEMENT
To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:
• ALWAYS keep keypads out of reach of children. NEVER permit children to
• ALWAYS keep keypads out of reach of children. NEVER permit children to
operate, or play with remote control transmitters/keypads.
• Activate gate or door ONLY when it can be seen clearly, is properly adjusted,
and there are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed. Never
permit anyone to cross path of moving gate or door.
Identify Your Garage Door Opener Brand
Determine your brand from an original hand held remote or locate the motor unit
receiver. The receiver can be mounted on the back or side panel of the motor unit
or could be mounted on the ceiling or wall.
receiver. The receiver can be mounted on the back or side panel of the motor unit
or could be mounted on the ceiling or wall.
You must choose a 4-digit Personal Identification Number (PIN) when
programming the CLK1. After programming is complete, your PIN plus any
additional number must be entered to activate your system.
programming the CLK1. After programming is complete, your PIN plus any
additional number must be entered to activate your system.
If an incorrect PIN is entered, the keypad flashes. When flashes stop, just re-enter
the correct PIN followed by any 5th additional number. (Do not use the * or # Key)
the correct PIN followed by any 5th additional number. (Do not use the * or # Key)
Clear and start over: Press * and # together until keypad stops flashing (5 sec.).
This erases previous programming and returns unit to unprogrammed factory setting.
This erases previous programming and returns unit to unprogrammed factory setting.
Keypad will flash: During certain programming sequences - when pressing the *
or # key or an incorrect PIN is entered.
or # key or an incorrect PIN is entered.
To program a second garage door opener brand after successfully programming
the first: Determine brand, then follow the brand steps, choosing a different PIN
and in step 1 enter 4,5,6,7 instead of 1,2,3,4. If unsuccessful, wait until keypad
stops flashing, then begin at step 1. Do not clear and start over as first door
programming will be erased.
the first: Determine brand, then follow the brand steps, choosing a different PIN
and in step 1 enter 4,5,6,7 instead of 1,2,3,4. If unsuccessful, wait until keypad
stops flashing, then begin at step 1. Do not clear and start over as first door
programming will be erased.
Keypad will light steadily for 5 seconds: After pressing any key or after entering
a correct PIN. Once programmed, the keypad remains active for 15 seconds.
During this time you may stop, reverse or reactivate the door by pressing any
number on the keypad.
a correct PIN. Once programmed, the keypad remains active for 15 seconds.
During this time you may stop, reverse or reactivate the door by pressing any
number on the keypad.
MOUNTING THE CLK1
Select a smooth vertical surface. Mount the keypad out of the path of the moving
garage door, but within sight of it. At least 4 inches of clearance is needed above
the keypad in order to slide the cover up.
Select a smooth vertical surface. Mount the keypad out of the path of the moving
garage door, but within sight of it. At least 4 inches of clearance is needed above
the keypad in order to slide the cover up.
Slide outside cover up and remove. Remove battery cover. Take battery out of
compartment (it is not necessary to disconnect it). Mount the keypad using the
two mounting holes and screws supplied, then reinsert battery, replace battery
cover, and slide outside cover down.
compartment (it is not necessary to disconnect it). Mount the keypad using the
two mounting holes and screws supplied, then reinsert battery, replace battery
cover, and slide outside cover down.
CHANGING YOUR PIN
It is not necessary to reprogram the CLK1 to change the existing PIN.
It is not necessary to reprogram the CLK1 to change the existing PIN.
To change your PIN:
■ Enter existing 4-digit PIN and the * key.
■ Enter existing 4-digit PIN and the * key.
■ Enter new 4-digit PIN and the * key.
■ To test, enter new 4-digit PIN followed by any 5th additional number.
Note: Do not use the * or # keys as a 5th number.
SECTION BRAND
1
Chamberlain, Sears, LiftMaster, Master Mechanic, Do It -
(9 Code Switch Systems, Yellow, White or Gray Learn Button)
(9 Code Switch Systems, Yellow, White or Gray Learn Button)
2
Chamberlain, Sears, LiftMaster, Master Mechanic, Do It -
(Green Learn Button)
(Green Learn Button)
3
Chamberlain, Sears, LiftMaster,
Master Mechanic, Do It - (Orange Learn Button)
Master Mechanic, Do It - (Orange Learn Button)
4
Linear, Moore-O-Matic
5
Genie - (9 Code Switch Systems)
6
Genie - (12 Code Switch Systems)
7
Multi-Code
8
Stanley
Circle your
Brand and
proceed to the
appropriate
section.
Helpful Hints
1
2 3 4
5 6
7 8
9
Step 1
Enter 1 2 3 4 and the * key.
Step 2
Enter your PIN and the * key.
Step 3
Enter your PIN and the # key.
Step 4
Enter 1 and the # key.
Step 5
Enter code in sequence from the TABLE above and the # key.
Programming is complete.
Programming is complete.
CODE SWITCH SEQUENCE
✚
0
–
PROGRAMMING
BATTERY REPLACEMENT
Replace the 9-volt battery when the keypad light becomes dim or does not light
up. Slide the outside cover up, unscrew the battery cover and replace battery. It
may be necessary to reprogram the keypad after battery is replaced.
Replace the 9-volt battery when the keypad light becomes dim or does not light
up. Slide the outside cover up, unscrew the battery cover and replace battery. It
may be necessary to reprogram the keypad after battery is replaced.
The Clicker can be
programmed to operate
with different brands of
garage door openers.
programmed to operate
with different brands of
garage door openers.
It is compatible with most
garage door opener
systems manufactured by
Chamberlain, Do It, Genie,
LiftMaster, Linear, Master
Mechanic, Moore-O-Matic,
Multi-Code, Sears and
Stanley.
garage door opener
systems manufactured by
Chamberlain, Do It, Genie,
LiftMaster, Linear, Master
Mechanic, Moore-O-Matic,
Multi-Code, Sears and
Stanley.
✱
7
4
1
0
8
5
2
#
9
6
3
Motor Unit
And Receiver
And Receiver
5 GENIE (9 CODE SWITCH SYSTEMS)
6 GENIE (12 CODE SWITCH SYSTEMS)
6 GENIE (12 CODE SWITCH SYSTEMS)
Locate your systems code switch positions from an original hand held remote or
the motor unit receiver. If the switch is “on” or “up”, place a 1; “off” or “down”,
place a 2 in the corresponding box in the TABLE below.
the motor unit receiver. If the switch is “on” or “up”, place a 1; “off” or “down”,
place a 2 in the corresponding box in the TABLE below.
Choose a 4-digit Personal Identification Number (PIN). Any combination of
numbers from 0 to 9 may be used.
numbers from 0 to 9 may be used.
Write PIN here:
To test enter PIN followed by any 5th additional number.
Note: Do not use the * star or # pound keys as a 5th number.
Note: Do not use the * star or # pound keys as a 5th number.
If programming is unsuccessful:
• Clear and start over.
• Check to be sure code from table above matches switch positions.
• Reverse code from table above (change 1 to 2; 2 to 1)
• Clear and start over.
• Check to be sure code from table above matches switch positions.
• Reverse code from table above (change 1 to 2; 2 to 1)
©2001, Clicker Corporation
114A2517
All Rights Reserved
Printed in Mexico
TECHNICAL SUPPORT: 800-442-1255
(MONDAY-FRIDAY 6AM-7PM CST; SATURDAY 8AM-6PM)
Chamberlain, LiftMaster and Moore-O-Matic are Trademarks of Chamberlain Group. Genie is a Trademark of Overhead Door Corporation. Linear and Multi-Code are
Trademarks of Linear Corporation. Master Mechanic is a Trademark of TruServ. Sears is a Trademark of Sears & Roebuck. Stanley is a Trademark of The Stanley Works.
Do It is a Trademark of Do It Best Corporation.
1
2 3 4
5 6
7 8
9 10 11 12
CODE SWITCH SEQUENCE
ON/UP
OFF/DOWN
Step 1
Enter 1 2 3 4 and the * key.
Step 2
Enter your PIN and the * key.
Step 3
Enter your PIN and the # key.
Step 4
GENIE (9 Code Switch Systems) - Enter 5 and the # key.
GENIE (12 Code Switch Systems) - Enter 6 and the # key.
GENIE (12 Code Switch Systems) - Enter 6 and the # key.
Step 5
Enter code in sequence from the TABLE above and the # key.
Programming is complete.
Programming is complete.
Step 1
Enter 1 2 3 4 and the * key.
Step 2
Enter your PIN and the * key.
Step 3
Enter your PIN and the # key.
Step 4
GREEN LEARN BUTTON Enter 2 and the # key.
ORANGE LEARN BUTTON Enter 3 and the # key.
ORANGE LEARN BUTTON Enter 3 and the # key.
Step 5
Press and release smart-learn button on motor unit. (indicator light
next to smart-learn button should turn on.)
next to smart-learn button should turn on.)
Step 6
Enter your PIN into the keypad.
Step 7
Press and HOLD any additional number on the keypad until the
indicator light next to the smart-learn button blinks.
Note: Do not use the * or # keys as a 5th number.
Programming is complete.
indicator light next to the smart-learn button blinks.
Note: Do not use the * or # keys as a 5th number.
Programming is complete.
PROGRAMMING
To test enter PIN followed by any 5th additional number.
Note: Do not use the * or # keys as the 5th number.
Note: Do not use the * or # keys as the 5th number.
PROGRAMMING
7 MULTI-CODE • 8 STANLEY
Locate your systems code switch positions from an original hand held remote or
the motor unit receiver. If the switch is “on” or “up”, place a 1; “off” or “down”,
place a 2 in the corresponding box in the TABLE below.
the motor unit receiver. If the switch is “on” or “up”, place a 1; “off” or “down”,
place a 2 in the corresponding box in the TABLE below.
Choose a 4-digit Personal Identification Number (PIN). Any combination of
numbers from 0 to 9 may be used.
numbers from 0 to 9 may be used.
Write PIN here:
To test enter PIN followed by any 5th additional number.
Note: Do not use the * star or # pound keys as a 5th number.
Note: Do not use the * star or # pound keys as a 5th number.
If programming is unsuccessful:
• Clear and start over.
• Check to be sure code from table above matches switch positions.
• Reverse code from table above (change 1 to 2; 2 to 1)
• Stanley brands try as Multi-Code, Multi-Code brands try as Stanley.
• Clear and start over.
• Check to be sure code from table above matches switch positions.
• Reverse code from table above (change 1 to 2; 2 to 1)
• Stanley brands try as Multi-Code, Multi-Code brands try as Stanley.
Step 1
Enter 1 2 3 and the * key.
Step 2
Enter your PIN and the * key.
Step 3
Enter your PIN and the # key.
Step 4
MULTI-CODE - Enter 7 and the # key.
STANLEY - Enter 8 and the # key.
STANLEY - Enter 8 and the # key.
Step 5
Enter code in sequence from the TABLE above and the # key.
Programming is complete.
Programming is complete.
PROGRAMMING
1
2 3 4
5 6
7 8
9 10
CODE SWITCH SEQUENCE
ON/UP
OFF/DOWN
4 LINEAR AND MOORE-O-MATIC
Locate your systems code switch positions from an original hand held remote or
the motor unit receiver. If the switch is “on” or “up”, place a 1; “off” or
“down”, place a 2 in the corresponding box in the TABLE below.
the motor unit receiver. If the switch is “on” or “up”, place a 1; “off” or
“down”, place a 2 in the corresponding box in the TABLE below.
Choose a 4-digit Personal Identification Number (PIN). Any combination of
numbers from 0 to 9 may be used.
numbers from 0 to 9 may be used.
Write PIN here:
To test enter PIN followed by any 5th additional number.
Note: Do not use the * star or # pound keys as a 5th number.
Note: Do not use the * star or # pound keys as a 5th number.
If programming is unsuccessful:
• Clear and start over.
• Check to be sure code from table above matches switch positions.
• Reverse code from table above (change 1 to 2; 2 to 1)
• Clear and start over.
• Check to be sure code from table above matches switch positions.
• Reverse code from table above (change 1 to 2; 2 to 1)
1
2 3 4
5 6
7 8
CODE SWITCH SEQUENCE
ON/UP
OFF/DOWN
Step 1
Enter 1 2 3 4 and the * key.
Step 2
Enter your PIN and the * key.
Step 3
Enter your PIN and the # key.
Step 4
Enter 4 and the # key.
Step 5
Enter code in sequence from the TABLE above and the # key.
Programming is complete.
Programming is complete.
PROGRAMMING
2 GREEN LEARN BUTTON
3 ORANGE LEARN BUTTON
3 ORANGE LEARN BUTTON
SYSTEMS WITH SMART-LEARN BUTTON
Locate your smart-learn button on your system. It will be located on the side or
back panel of the motor unit (near the small grey wire antenna).
back panel of the motor unit (near the small grey wire antenna).
The original hand held remote will not have code switches.
Choose a 4-digit Personal Identification Number (PIN). Any combination of
numbers from 0 to 9 may be used.
numbers from 0 to 9 may be used.
Write PIN here: