Inovonics Wireless Corporation 3B6RTA Manuel D’Utilisation
© 1999 Inovonics
support@inovonics.com phone: 800.782.2709
www.inovonics.com
f223_v1.fm rev 1.00 8/20/99
Intended use: The FA223S portable transmitter utilizes Inovon-
ics 900MHz Frequency Agile
ics 900MHz Frequency Agile
®
technology. The transmitter,
intended to be installed and serviced by licensed security profes-
sionals, transmits messages to an Inovonics receiver.
sionals, transmits messages to an Inovonics receiver.
The FA223S has a water-resistant housing suitable for use in
showers and bathtubs. It is not, however, designed for prolonged
submersion, or for subermersion deeper than one foot.
showers and bathtubs. It is not, however, designed for prolonged
submersion, or for subermersion deeper than one foot.
•
To activate the FA223S, press and hold the Transmit Button for at least
1 second. (Actual minimum activation interval is .700 second.)
1 second. (Actual minimum activation interval is .700 second.)
•
Alarm signals are transmitted multiple times, and are indicated by the
blinking transmit LED.
blinking transmit LED.
•
Holding the button results in continuous transmission.
•
When the button is released, the FA223S will complete its alarm trans-
mission, then will send an alarm restoral signal.
mission, then will send an alarm restoral signal.
Dimensions:
2.22" x 1.925" x0.725"
Weight: 1.4 oz.
External contacts:N/O
Typical battery life:
1 to 2 years
Battery (BAT609): 3.0V lithium Sanyo CR2450
—or— Renata CR2450N
(The battery is always supervised.)
1. Open the transmitter housing by removing three phillips-head screws.
2. When prompted by the programming device to plug in the transmitter,
2. When prompted by the programming device to plug in the transmitter,
connect the programming cable to the 3-pin programming header.
3. Press the internal reset button.
4. Disconnect the programming cable.
5. Re-assemble and thoroughly test the transmitter.
4. Disconnect the programming cable.
5. Re-assemble and thoroughly test the transmitter.
NOTE: FA223S transmitters retain programming data in non-volatile mem-
ory. They do not require reprogramming after loss of power. Install new bat-
tery and press either the internal or the external reset button to re-initialize
the transmitter and restore programming.
ory. They do not require reprogramming after loss of power. Install new bat-
tery and press either the internal or the external reset button to re-initialize
the transmitter and restore programming.
IMPORTANT: The FA223S should always be programmed for supervision.
I
I
Inovonics recommends that pendants always be supervised.
Pendants should also be tested at least once per week.
Suggested check-in interval: 5 minutes
External contacts:
N/O
I
I
For information on supervision programming options, request
Tech Notes TN1025 and TN1032.
The FA223S can be carried in 3 convienient ways:
• Around the neck as a pendant (standard).
• On a belt with the beltclip attachment (standard).
• On the arm with optional wristband accessory (ACC634W).
• On a belt with the beltclip attachment (standard).
• On the arm with optional wristband accessory (ACC634W).
I
I
Caution: Neck Cord Safety
WARNING:
The neck cord provided with the FA223S is designed for user safety.
Substitution of stronger cords or chains may result in injury to the
wearer.
Substitution of stronger cords or chains may result in injury to the
wearer.
External
Transmit LED
Transmit
Button
Reset Button
FA223S Single-button Pendant transmitter
Operation
Specifications
Changing the battery:
1) Remove 3 screws from the
back of the housing.
2) Make sure that the battery is
inserted with the positive (+) ter-
minal facing the indicated side of
the holder.
3) After replacing the battery,
press the internal reset button to
reset the transmitter to its most
recent programming.
4) Replace back cover and care-
fully re-tighten screws evenly for
tight seal
5) Thoroughly test the unit before
returning to service.
1) Remove 3 screws from the
back of the housing.
2) Make sure that the battery is
inserted with the positive (+) ter-
minal facing the indicated side of
the holder.
3) After replacing the battery,
press the internal reset button to
reset the transmitter to its most
recent programming.
4) Replace back cover and care-
fully re-tighten screws evenly for
tight seal
5) Thoroughly test the unit before
returning to service.
Internal
Reset Button
3-pin
programming
header
Battery Positive
Indicator
Indicator
Changing the battery
Programming
Factory Default
/
Recommended Programming
Belt Clip
Neck cord Clip
Wrist Band (optional)
(ACC623W)
Recommended method of attaching
the neck cord to the FA223S
Wearing the FA223S: Neck cord, Belt Clip or Wrist Band
FA223S
Installation
Instructions
Instructions