ZyXEL Communications Corporation B320 Manuel D’Utilisation
ZyAIR Wireless LAN Utility
Using the ZyAIR Utility
2-15
RTS/CTS Threshold is designed to prevent collisions due to hidden nodes. An RTS/CTS Threshold
defines the biggest size data frame you can send before an RTS (Request To Send)/CTS (Clear to Send)
handshake is invoked.
When a data frame exceeds the RTS/CTS Threshold value you set (between 0 to 2432 bytes), the station
that wants to transmit this frame must first send an RTS (Request To Send) message to the AP for
permission to send it. The AP then responds with a CTS (Clear to Send) message to all other stations within
its range to notify them to defer their transmission. It also reserves and confirms with the requesting station
the time frame for the requested transmission.
Stations can send frames smaller than the specified RTS/CTS Threshold directly to the AP without the
RTS (Request To Send)/CTS (Clear to Send) handshake.
You should only configure RTS/CTS Threshold if the possibility of hidden nodes exists on your network
and the “cost” of resending large frames is more than the extra network overhead involved in the RTS
(Request To Send)/CTS (Clear to Send) handshake.
If the RTS/CTS Threshold value is greater than the Fragmentation Threshold value (see next), then the
RTS (Request To Send)/CTS (Clear to Send) handshake will never occur as data frames will be fragmented
before they reach RTS/CTS Threshold size.
defines the biggest size data frame you can send before an RTS (Request To Send)/CTS (Clear to Send)
handshake is invoked.
When a data frame exceeds the RTS/CTS Threshold value you set (between 0 to 2432 bytes), the station
that wants to transmit this frame must first send an RTS (Request To Send) message to the AP for
permission to send it. The AP then responds with a CTS (Clear to Send) message to all other stations within
its range to notify them to defer their transmission. It also reserves and confirms with the requesting station
the time frame for the requested transmission.
Stations can send frames smaller than the specified RTS/CTS Threshold directly to the AP without the
RTS (Request To Send)/CTS (Clear to Send) handshake.
You should only configure RTS/CTS Threshold if the possibility of hidden nodes exists on your network
and the “cost” of resending large frames is more than the extra network overhead involved in the RTS
(Request To Send)/CTS (Clear to Send) handshake.
If the RTS/CTS Threshold value is greater than the Fragmentation Threshold value (see next), then the
RTS (Request To Send)/CTS (Clear to Send) handshake will never occur as data frames will be fragmented
before they reach RTS/CTS Threshold size.
Enabling the RTS Threshold causes redundant network overhead that could
negatively affect the throughput performance instead of providing a remedy.
2.7.3 Authentication Type
The IEEE 802.11b standard describes a simple authentication method between the wireless clients and AP.
Three authentication modes are defined: Auto, Open and Shared.
Open authentication mode is implemented for ease-of-use and when security is not an issue. The wireless
station and the AP do not share a secret key. Thus the wireless stations can associate with any AP and listen
to any data transmitted plaintext.
Shared authentication mode involves a shared secret key to authenticate the wireless station to the AP. This
requires you to enable a security feature and specify a shared secret key (usually the WEP encryption and
WEP key) on both the wireless station and the AP.
Auto authentication mode allows the ZyAIR to switch between the open and shared key authentication
modes automatically. Use the auto mode if you do not know the authentication mode of the other wireless
clients.
Three authentication modes are defined: Auto, Open and Shared.
Open authentication mode is implemented for ease-of-use and when security is not an issue. The wireless
station and the AP do not share a secret key. Thus the wireless stations can associate with any AP and listen
to any data transmitted plaintext.
Shared authentication mode involves a shared secret key to authenticate the wireless station to the AP. This
requires you to enable a security feature and specify a shared secret key (usually the WEP encryption and
WEP key) on both the wireless station and the AP.
Auto authentication mode allows the ZyAIR to switch between the open and shared key authentication
modes automatically. Use the auto mode if you do not know the authentication mode of the other wireless
clients.
2.7.4 Preamble Type
A preamble is used to synchronize the transmission timing in your wireless network. There are two
preamble modes: Long Preamble and Short Preamble.
Short preamble takes less time to process and minimizes overhead, so it should be used in a good wireless
network environment when all wireless clients support it.
preamble modes: Long Preamble and Short Preamble.
Short preamble takes less time to process and minimizes overhead, so it should be used in a good wireless
network environment when all wireless clients support it.