ZyXEL Communications Corporation PRESTIGE310S Manuel D’Utilisation
Prestige 310 Broadband Sharing Gateway
Hardware Installation & Initial Setup
2-3
For the initial configuration of your Prestige, you need to use terminal emulator software on a workstation
and connect it to the Prestige through the console port. Connect the 9-pin (smaller) end of the console cable
to the console port of the Prestige and the 25-pin (bigger) end to a serial port (COM1, COM2 or other COM
port) of your workstation. You can use an extension RS-232 cable if the enclosed one is too short. After the
initial setup, you can modify the configuration remotely through telnet connections.
and connect it to the Prestige through the console port. Connect the 9-pin (smaller) end of the console cable
to the console port of the Prestige and the 25-pin (bigger) end to a serial port (COM1, COM2 or other COM
port) of your workstation. You can use an extension RS-232 cable if the enclosed one is too short. After the
initial setup, you can modify the configuration remotely through telnet connections.
Step 2.
Connecting the Prestige to the Broadband Modem
Please use the cable supplied with your broadband modem to connect the broadband
modem and the Prestige.
Step 2a.
Connecting the Prestige to the Cable Modem
Connect the WAN port (silver) on the Prestige to the Ethernet port on the cable modem using a straight
through Ethernet cable. The Ethernet port on the cable modem is sometimes labeled "PC" or "Workstation".
through Ethernet cable. The Ethernet port on the cable modem is sometimes labeled "PC" or "Workstation".
OR
Step 2b.
Connecting the Prestige to the xDSL Modem
Connect the WAN port (silver) on the Prestige to the Ethernet port on the xDSL modem using a straight
through Ethernet cable.
Step 3.
through Ethernet cable.
Step 3.
Connecting the Prestige to the LAN
When the Prestige Ethernet cable is correctly connected to the PC or hub, the front
panel LAN will go on.
To connect to a single PC, connect the 10/100M LAN port on the Prestige to the Network Adapter on the PC
using the white straight through cable and depress the Uplink button (“on”). If you do not depress the Uplink
button, you must use a crossover cable for this connection. If you have more than one PC, you must use an
external hub. Connect the 10/100M LAN port (gold) on the Prestige to a port on the hub using a straight
through Ethernet cable and make sure the Uplink button is not depressed (“on”).
Step 4.
using the white straight through cable and depress the Uplink button (“on”). If you do not depress the Uplink
button, you must use a crossover cable for this connection. If you have more than one PC, you must use an
external hub. Connect the 10/100M LAN port (gold) on the Prestige to a port on the hub using a straight
through Ethernet cable and make sure the Uplink button is not depressed (“on”).
Step 4.
Connecting the Power Adapter to your Prestige
Connect the power adapter to the port labeled POWER on the rear panel of your Prestige.
Step 5.
Step 5.
Grounding the Prestige (Optional)
Ground the Prestige by connecting a grounded wire to the F.G. (Frame Ground) of the Prestige.
2.3 Additional
Installation
Requirements
In addition to the contents of your package, there are other hardware and software requirements you need
before you can install and use your Prestige. These requirements include:
1. A computer with an Ethernet NIC (Network Interface Card) installed.
2. A computer equipped with communications software called terminal emulation software configured to
before you can install and use your Prestige. These requirements include:
1. A computer with an Ethernet NIC (Network Interface Card) installed.
2. A computer equipped with communications software called terminal emulation software configured to
the following parameters:
♦
VT100 terminal emulation.
♦
9600 Baud.