JTS Professional Co Ltd TG-64T Manuel D’Utilisation

Power Switch and

Volume Control

Power Switch and

Volume Control

3.5mm Earphone

Output Jack 

3.5mm Microphone 

Input Jack 

3.5mm Line Out



Always make all connections before plugging the unit 
into an AC power outlet. 



Do not leave the devices in a place with high temperature 
or high humidity.



Always do not handle the power cord with wet hands !





operation, and recharge if no use for over three months.

 
















Charger Slot

DC input (12V)

Charging Indicator

Neck-Strap

WM-10TG

Mono Earphone ( For TG-64R/RA)

Number of charging slot

Power requirement

LED Indicator

Dimensions(mm)

2 (receiver or transmitter)

12-18 VDC , 600mA 

Power connected: Flash green

Charging : Green

85mm(W)* 75mm(D)* 41mm(H) 

18.5 cm

PLL Synthesized Control

502MHz~960MHz

Channel Power On/Off, 

Channel selection Volume control,

Group selection, Limiter

40~18,000Hz

1/8” Dummy stereo Phone Jack

10 hours typical

Rechargeable NIMH AA (1.2V,2000mAh)

62mm(W)* 20mm(D)* 97mm(H)  

Frequency Preparation

Carrier Frequency Range

Controls

Audio Frequency Response

Output connector

Battery life

Battery

Dimension(mm)

Internal Microphone

Frequency Preparation

Carrier Frequency Range

RF Outputs

Stability

Frequency Deviation

Controls

Spurious Emissions

Audio Frequency Response

Microphone input connector

Battery life

Battery

Dimension(mm)

Omni-directional Condenser Microphone

PLL Synthesized Control

502MHz~960MHz

10mW

±10kHz

±48kHz

Power On/Off, Channel selection, 

Volume control, Group selection, Boost

<-50 dBC

40~18,000 Hz

1/8” Mono Phone Jack

10 hours typical

Rechargeable NIMH AA (1.2V, 2000mAh)

62mm(W)* 20mm(D)* 97mm(H) 

Optional : CM-201 omnidirectional

Lavaliere Microphone

(For TG-64T/TA)

CM-801S omnidirectional

Earhook Microphone

(For TG-64T/TA)

PANTONE 425C

Adaptor (110/230V input, 600mA 12V output)

TG-64T/TG-64TA

Use the “Belt-Clip” and 

the “external Microphone”

Use the “Neck-Strap” 

and the 

“external Microphone”

TG-64R/TG-64RA  

Use the “Belt-Clip”

and the “Mono Earphone”

Use the “Neck-Strap” 

and the 

“Mono Earphone”

Plug the TG-64T/TG-64R (Charger Connector faces 

down) into “Charger Slot” in TG-64CH2.The “Charging 

testing, and then show green light when charging. It 

Notice 1 :  As soon as AC power is connected, the

  

Notice 2 : 

for selt-testing during charging to protect batteries 

from being damaged.

59516-004

 Power On / OFF and Volume Control



 Notice.1: The channel and group of the transmitter 

(TG-64T) must match that of the receiver (TG-64R). 

Connect Microphone or Earphone
TG-64T/TG-64TA :  Plug “External Microphone” into “

3.5mm Microphone Input Jack” 

TG-64R/TG-64RA :  Plug “an earphone” into “3.5mm 

Earphone Output Jack”

Power Switch and Volume Control

TG-10R

Earhook Microphone

CM-801S

1856

說明書 雙面.N字三摺.JTS TG-64R/64T/64RA/64TA (185*250mm)含塑膠袋-01版

59516-004

TG-64 is designed on the base of the TG-10 successful 

experience plus JTS very recent innovative ideas.

UHF PLL 64 channels in 4 groups

Maximum operational distance ( in line of sight )

TG-64R : 180m

TG-64RA : 280m

Use rechargeable AA battery

Built in transmission power selector 

Built in audio output limiter

Line in at TX and Line Out at RX ready for video camera

Transmitter bundled with tie clip microphone CM-201

Receiver bundled with single earphone WM-10TG

Built in speaker at TG-64R/RA

Built in microphone at TG-64T/TA

Compatible with stationary transmitter TG-10GSTX and 

receiver TG-10GSRX

3.5mm Line In

Built-in Speaker

Antenna

Channel Selector

LED Power Indicator

Belt Clip

Charger Connector

Use the “Neck-Strap” 

and the 

“Built-in Microphone”

Turn on or off the power and adjust the volume by 

rotating the volume control clockwise and reversely. 

Noted: Please turn off the receiver/transmitter 

before replacing batteries to ensure all functions 

normal. 

Select a desired channel for the receiver / transmitter 

by rotating the channel selector. (0-9,A-F)

Use the supplied plastic stick to select a desired group 

for the receiver/transmitter. (A-D)

6.3 cm

6.2 cm

6.2 cm

6.3 cm