Risco Ltd. RW132KLXP1356 Manuel D’Utilisation
1
Model:
RW132KL1P; RW132KL2P
EN
Installation Instructions
EN
1 General Description
The Wireless 2-Way Slim Keypad empowered with a proximity
reader comes in two models:
RW132KL1PUSA — a black protection-insulated outdoor model
reader comes in two models:
RW132KL1PUSA — a black protection-insulated outdoor model
RW132KL2PUSA — a white indoor model
The keypad operates in either of two modes:
• Full function Mode: Wireless LED operating keypad
• Bypass unit Mode: Used to activate an entry countdown period
Being bi-directional the 2-Way keypad receives a reply status indication
from the panel for each command that it has sent to the panel.
To use functions of the keypad you can use a proximity tag or a code.
• Full function Mode: Wireless LED operating keypad
• Bypass unit Mode: Used to activate an entry countdown period
Being bi-directional the 2-Way keypad receives a reply status indication
from the panel for each command that it has sent to the panel.
To use functions of the keypad you can use a proximity tag or a code.
2 Activating the Batteries
Remove the batteries red strip to activate the batteries.
3 Quick Device Allocation at the Control Panel
The Keypad is automatically programmed to your control panel
during the on-line installation wizard setup. If you later purchase an
extra keypad you can enroll it as follows:
To quickly allocate a keypad at the control panel:
If the control panel is not already in Learn mode, press the
during the on-line installation wizard setup. If you later purchase an
extra keypad you can enroll it as follows:
To quickly allocate a keypad at the control panel:
If the control panel is not already in Learn mode, press the
button on the control panel for 5 seconds; the unit beeps once
as it enters Learn mode (all the LEDs also light up, one after the
other).
Make sure batteries are installed in each keypad before allocating
them.
other).
Make sure batteries are installed in each keypad before allocating
them.
Send a signal transmission from the keypad by pressing
and
simultaneously for at least 2 seconds; the control panel beeps
once to accept or beeps three times to reject. Once accepted, the
system announces the device type and its zone (for example,
“Keypad, zone 1”).
When the keypads have been enrolled, short-press the control panel
system announces the device type and its zone (for example,
“Keypad, zone 1”).
When the keypads have been enrolled, short-press the control panel
button
to exit Learn mode; the unit beeps once and the LEDs
stop flashing.
Note:
Note:
For future use, it is recommended to write down the keypad
description, zone number, and installation location of each allocated
keypad.
keypad.
4 Buzzer and LED Indications
Buzzer Indications:
Duration
Operation
Long beep
Confirmation
3 short beeps
Wrong code
Pulsed beeps
Exit/enty beeps (programmable)
Short beep
Each key press
LED Indciations:
Color
State
Status
Blue
Blink
During communcation with the
panel
panel
Red
On
Slow flash
Rapid flash
Slow flash
Rapid flash
System fully or partially armed
During Exit dealy
During alarm
During Exit dealy
During alarm
Green
Blink
Trouble indication in the
system while the system is
unset
system while the system is
unset
Green/Red toggle
Toggle
Waiting for code to be
entered
entered
5 Using the Proxmity Tag
The proximity tag, is correctly
used by applying it within a
used by applying it within a
2 cm distance from the
key as shown in the
illustration (after waking the
keypad by pressing the
appropriate key).
illustration (after waking the
keypad by pressing the
appropriate key).
6 Common Operations
Operation
Quick
High security mode
1
Set (Away Arm)
Press
Press
2
Part Set (Stay Arm)
3
Press
Press
2
Unset (Disarm)
1. Press
> Code or 2. Proximity tag
(after wakeup)
Notes:
1. Consult your installer for the operations defined with a code.
2. The proximity tag can be used instead of code.
3. For Part Setting (Stay Arming) with no entry delay press the
key for
two seconds.
7 Technical Specifications
Battery type
CR123, 3V lithium battery (x 2)
Current consumption
10µA stand by; 100 mA Max.
Battery life
3 years (for typical use)
Frequency
13.56MHz
Operating/storage temperature
-40° – 70°C (-40° – 159°F)
Dimensions
100 mm X 45 mm X 25 mm (3.9 x
1.8 x .98 inches)
1.8 x .98 inches)
Weight (incl batteries)
0.157 kg
Blue Red Green
2W WL White Slim Int. KP+Prox915
2W WL White Slim Int. KP+Prox915