Risco Ltd. RWX73F915 Manuel D’Utilisation
Door / Window Sensor
Model: RWX73F/RWX73M
EN
Installation instructions
EN
1 General Description
The RWX73 is a 2-way door / window sensor that offers protection
against opening doors and windows, and against any attempt to
tamper with the detector using large magnets.
against opening doors and windows, and against any attempt to
tamper with the detector using large magnets.
2 Quick Device Allocation at the Control Panel
The sensor is automatically programmed to your control panel during
the on-line installation wizard setup. If you later purchase an extra
sensor you can enroll it as follows:
To quickly allocate the sensor at the control panel:
the on-line installation wizard setup. If you later purchase an extra
sensor you can enroll it as follows:
To quickly allocate the sensor at the control panel:
If the control panel is not already in Learn mode, press the
button on the control panel for 5 seconds; the unit beeps once
as it enters Learn mode (all the LEDs also light up, one after the
other).
Remove the plastic wrapping from the batteries before installation
and make sure the cover is removed so the internal tamper switch is
accessible.
Send a signal transmission from the detector by pressing the tamper
button for at least 2 seconds; the control panel beeps once to accept or
beeps three times to reject. Once accepted, the system announces the
device type and its zone (for example, “Sensor, zone 1”).
When the sensors have been enrolled, short-press the control panel
other).
Remove the plastic wrapping from the batteries before installation
and make sure the cover is removed so the internal tamper switch is
accessible.
Send a signal transmission from the detector by pressing the tamper
button for at least 2 seconds; the control panel beeps once to accept or
beeps three times to reject. Once accepted, the system announces the
device type and its zone (for example, “Sensor, zone 1”).
When the sensors have been enrolled, short-press the control panel
button
to exit Learn mode; the unit beeps once and the LEDs
stop flashing.
Note:
Note:
For future use, it is recommended to write down the sensor
description, zone number, and installation location of each allocated
detector.
detector.
3 LED Indication
•
Upon successful learning: short flash sequence
•
Normal operation: brief light upon transmission
•
Low battery: short flash sequence during transmission
Selecting the Mounting Location
1. Select a location best suited for communication quality and near
the intended wired detector. RISCO recommends placing the unit
at the highest possible position.
at the highest possible position.
2. Temporarily attach the unit to this point using the two-sided
adhesive tape.
3. Generate an alarm signal and verify that the receiver has received
the signal. If the alarm signal is not detected, reposition the sensor
and try again.
and try again.
4 Technical Specifications
Electrical
Battery Type
CR123 3V Lithium Battery
Current consumption
22µA standby
Frequency
915 MHz
Dead Time (HOLD ON)
2.5 minutes
Supervision Transmission
0-255 minutes
Battery Life
3 years typical
Contact size
32 x 35 x 72 mm (1.3 x 1.4 x 2.8 in.)
Magnet Size: 16 x 11 x 72 mm (0.6 x
0.44 x 2.8 in.)
Magnet Size: 16 x 11 x 72 mm (0.6 x
0.44 x 2.8 in.)
Environmental
Operating temperature
Operating temperature
0°C to 40°C (32°F to 104°F)
Storage temperature
20°C to 60°C (-4°F to 140°F)
* Specifications are subject to change without prior notice
RISCO Group Limited Warranty
RISCO Group and its subsidiaries and affiliates ("Seller") warrants its products to be free from
defects in materials and workmanship under normal use for 24 months from the date of
production. Because Seller does not install or connect the product and because the product may
be used in conjunction with products not manufactured by the Seller, Seller can not guarantee
the performance of the security system which uses this product. Sellers' obligation and liability
under this warranty is expressly limited to repairing and replacing, at Sellers option, within a
reasonable time after the date of delivery, any product not meeting the specifications. Seller
makes no other warranty, expressed or implied, and makes no warranty of merchantability or of
fitness for any particular purpose. In no case shall seller be liable for any consequential or
incidental damages for breach of this or any other warranty, expressed or implied, or upon any
other basis of liability whatsoever. Sellers obligation under this warranty shall not include any
transportation charges or costs of installation or any liability for direct, indirect, or not be
compromised or circumvented; that the product will prevent any persona; injury or property loss
by intruder, robbery, fire or otherwise; or that the product will in all cases provide adequate
defects in materials and workmanship under normal use for 24 months from the date of
production. Because Seller does not install or connect the product and because the product may
be used in conjunction with products not manufactured by the Seller, Seller can not guarantee
the performance of the security system which uses this product. Sellers' obligation and liability
under this warranty is expressly limited to repairing and replacing, at Sellers option, within a
reasonable time after the date of delivery, any product not meeting the specifications. Seller
makes no other warranty, expressed or implied, and makes no warranty of merchantability or of
fitness for any particular purpose. In no case shall seller be liable for any consequential or
incidental damages for breach of this or any other warranty, expressed or implied, or upon any
other basis of liability whatsoever. Sellers obligation under this warranty shall not include any
transportation charges or costs of installation or any liability for direct, indirect, or not be
compromised or circumvented; that the product will prevent any persona; injury or property loss
by intruder, robbery, fire or otherwise; or that the product will in all cases provide adequate
warning or protection. Buyer understands that a properly installed and maintained alarm may
only reduce the risk of intruder, robbery or fire without warning, but is not insurance or a guaranty
that such will not occur or that there will be no personal injury or property loss as a result.
Consequently seller shall have no liability for any personal injury, property damage or loss based
on a claim that the product fails to give warning. However, if seller is held liable, whether directly
or indirectly, for any loss or damage arising from under this limited warranty or otherwise,
regardless of cause or origin, sellers maximum liability shall not exceed the purchase price of the
product, which shall be complete and exclusive remedy against seller. No employee or
representative of Seller is authorized to change this warranty in any way or grant any other
warranty.
WARNING: This product should be tested at least once a week.
CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries
according to local regulations.
only reduce the risk of intruder, robbery or fire without warning, but is not insurance or a guaranty
that such will not occur or that there will be no personal injury or property loss as a result.
Consequently seller shall have no liability for any personal injury, property damage or loss based
on a claim that the product fails to give warning. However, if seller is held liable, whether directly
or indirectly, for any loss or damage arising from under this limited warranty or otherwise,
regardless of cause or origin, sellers maximum liability shall not exceed the purchase price of the
product, which shall be complete and exclusive remedy against seller. No employee or
representative of Seller is authorized to change this warranty in any way or grant any other
warranty.
WARNING: This product should be tested at least once a week.
CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries
according to local regulations.
FCC ID: JE4RWX73F915
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
Changes or modifications to this equipment which are not expressly approved by
the party responsible for compliance (RISCO Group's.) could void the user's
authority to operate the equipment.
FCC Note
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment on and off, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on to a different circuit from that to
which the receiver is connected.
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
© RISCO Group 07/16
5IN2579