Crestron Electronics Inc QMTDCDRP3 Manuel D’Utilisation
CSM-QMTDC-DRP-3-CN/CSM-QMTDC-DRP-3-EX
Digital QMT
Digital QMT
®
Drapery Track Motor
Programming Guide
Test the Motor Direction
Press the open or close button to move the drapery fabric. If the drapery fabric begins to
move in the other direction, the motor direction must be reversed.
To reverse the motor direction, press and hold the configure button for 10 seconds. The
red LED lights for 3 seconds. The drapery motor then immediately enters the Find Limit
sequence.
Press the open or close button to move the drapery fabric. If the drapery fabric begins to
move in the other direction, the motor direction must be reversed.
To reverse the motor direction, press and hold the configure button for 10 seconds. The
red LED lights for 3 seconds. The drapery motor then immediately enters the Find Limit
sequence.
NOTE: Reversing the direction of the motor erases all limits that have been previously
set. Follow the procedure in "Set up the Drapery Limits" to reassign limits. After either
the open or close limit is set, the motor automatically enters Limit Setup mode for the
opposite limit.
set. Follow the procedure in "Set up the Drapery Limits" to reassign limits. After either
the open or close limit is set, the motor automatically enters Limit Setup mode for the
opposite limit.
Controls and Indicators
The Crestron CSM-QMTDC-DRP-3 motors have open, configure, and close push
buttons that are used to program the drapery. The motors have a multicolor LED that
provides confirmation, operating mode, and error state feedback.
Crestron CSM-QMTDC-DRP-3 Motor Multicolor LED and Push Button Orientation
buttons that are used to program the drapery. The motors have a multicolor LED that
provides confirmation, operating mode, and error state feedback.
Crestron CSM-QMTDC-DRP-3 Motor Multicolor LED and Push Button Orientation
Test the Drapery
Before the drapery is operated, the motor must be tested to ensure that the motor
direction is correct and that the drapery travels correctly while being opened and closed.
direction is correct and that the drapery travels correctly while being opened and closed.
NOTE: Before using the CSM-QMTDC-DRP-3 motor, ensure the device is using the
latest firmware. Check for the latest firmware for the CSM-QMTDC-DRP-3 motor at
www.crestron.com/firmware. Firmware is loaded onto the device using Crestron
Toolbox
latest firmware. Check for the latest firmware for the CSM-QMTDC-DRP-3 motor at
www.crestron.com/firmware. Firmware is loaded onto the device using Crestron
Toolbox
™
.
Find Location
Find Location mode is an automatic reference detection procedure that the drapery
executes after power outage or power cycle.
During power outages the drapery can be manually opened or closed by the user, which
leaves the drapery motor unaware of the fabric location. Also, during initial power-up the
drapery motor does not know the location of the fabric. To solve this problem, the
drapery motor automatically enters Find Location mode after power is restored and a
command is given to go to a specific location such as full open or full close, or any set
position. When in Find Location mode, the drapery motor will run the drapery fabric to its
full close hard limit, and then it will go to the location that has been requested. The LED
blinks purple while in Find Location mode.
executes after power outage or power cycle.
During power outages the drapery can be manually opened or closed by the user, which
leaves the drapery motor unaware of the fabric location. Also, during initial power-up the
drapery motor does not know the location of the fabric. To solve this problem, the
drapery motor automatically enters Find Location mode after power is restored and a
command is given to go to a specific location such as full open or full close, or any set
position. When in Find Location mode, the drapery motor will run the drapery fabric to its
full close hard limit, and then it will go to the location that has been requested. The LED
blinks purple while in Find Location mode.
Speed Setup
The speed that the drapery fabric travels can be learned in Speed Setup mode.
1. Press and hold the open and configure push buttons for 4 seconds. The LED will
1. Press and hold the open and configure push buttons for 4 seconds. The LED will
turn blue.
2. Pull the fabric at the desired approximate speed for 2 seconds.
3. The blue LED turns off to indicate that the speed has been stored.
4. Operate the shade to ensure the desired speed setting has been achieved. This
3. The blue LED turns off to indicate that the speed has been stored.
4. Operate the shade to ensure the desired speed setting has been achieved. This
procedure may be repeated until the drapery runs at the desired speed.
NOTE: The drapery motor exits Speed Setup mode if it does not receive any input for
30 seconds.
30 seconds.
Touch Sensitivity Setup
The drapery motor will open or close with a pull of the drapery fabric. To set up the
sensitivity for how much force it takes to activate the drapery, use the following
procedure:
1. Press and hold the close and configure push buttons for 4 seconds. The LED will
sensitivity for how much force it takes to activate the drapery, use the following
procedure:
1. Press and hold the close and configure push buttons for 4 seconds. The LED will
turn purple.
2. Pull the fabric at the approximate force that the motor should react to.
3. The purple LED turns off to indicate that the touch sensitivity has been stored.
4. Pull the fabric with the same force applied in step 2 to open and close the drapery,
3. The purple LED turns off to indicate that the touch sensitivity has been stored.
4. Pull the fabric with the same force applied in step 2 to open and close the drapery,
and it should begin to open and close accordingly. This procedure may be
repeated until the drapery reacts to the desired sensitivity.
repeated until the drapery reacts to the desired sensitivity.
NOTE: The drapery motor exits Touch Sensitivity Setup mode if it does not receive
any input for 30 seconds.
any input for 30 seconds.
Joining an infiNET EX Network (infiNET EX Interfaces Only)
The device connects to the Crestron network via the infiNET EX
®
communications
protocol. Use the procedures outlined below to join or leave an infiNET EX network and
to verify communications between the device and the control system.
to verify communications between the device and the control system.
Joining an infiNET EX Network
Before an infiNET EX device can be used in a shading system, it must first join an infiNET
EX network. To join an infiNET EX network, the device must be acquired by an infiNET
EX gateway.
Before an infiNET EX device can be used in a shading system, it must first join an infiNET
EX network. To join an infiNET EX network, the device must be acquired by an infiNET
EX gateway.
NOTE
: A device can be acquired by only one gateway.
1. Put the infiNET EX gateway into Acquire mode from the unit itself or from Crestron
Toolbox. Refer to the gateway’s manual at www.crestron.com/manuals for details.
NOTE: In an environment where multiple gateways are installed, only one
gateway should be in the Acquire mode at any time.
gateway should be in the Acquire mode at any time.
2. Put the device into Acquire mode by doing the following:
a. Tap the configure button three times, and then press and hold it down
(tap-tap-tap-press+hold) until the white LED on the device blinks once (this can
take up to 10 seconds).
take up to 10 seconds).
b. Release the button to start the acquire process. The LED blinks slowly to show
that the device is actively scanning the infiNET EX network.
• The white LED turns on for 5 seconds to show that the device has been
successfully acquired by the infiNET EX network.
• The white LED blinks fast to indicate that the device was not successfully
acquired by the infiNET EX network. Tap a button to acknowledge the failure.
The LEDs time out automatically. Ensure the gateway is in Acquire mode and
within range before attempting the acquire process again.
The LEDs time out automatically. Ensure the gateway is in Acquire mode and
within range before attempting the acquire process again.
Leaving an infiNET EX Network
To leave an infiNET EX network, put the device into Acquire mode, as described in
“Joining an infiNET EX Network” above, when no gateway is in Acquire mode.
To leave an infiNET EX network, put the device into Acquire mode, as described in
“Joining an infiNET EX Network” above, when no gateway is in Acquire mode.
Verifying infiNET EX Communications Status
To check the communications status of the device, tap the configure button three times,
and then press and hold it down (tap-tap-tap-press+hold) for up to 2 seconds. The LED
blinks to indicate the communications status.
To check the communications status of the device, tap the configure button three times,
and then press and hold it down (tap-tap-tap-press+hold) for up to 2 seconds. The LED
blinks to indicate the communications status.
Description
The Crestron
®
digital QMT
®
CSM-QMTDC-DRP-3 motors are programmed locally using
the buttons on the motor or through a control system. The information in this guide
serves as a detailed programming overview of the Crestron CSM-QMTDC-DRP-3
drapery motors.
serves as a detailed programming overview of the Crestron CSM-QMTDC-DRP-3
drapery motors.
NOTE: The procedures described in this document can also be performed remotely
via a Crestron control system. The timeout and LED indicators are the same as
described in this document.
via a Crestron control system. The timeout and LED indicators are the same as
described in this document.
NOTE: Before using the CSM-QMTDC-DRP-3, ensure the device is using the latest
firmware. Check for the latest firmware for the CSM-QMTDC-DRP-3 at
www.crestron.com/firmware. Firmware is loaded onto the device using Crestron
Toolbox™.
firmware. Check for the latest firmware for the CSM-QMTDC-DRP-3 at
www.crestron.com/firmware. Firmware is loaded onto the device using Crestron
Toolbox™.
Set Up the Drapery Limits
The drapery motor needs to establish its hard limits (beginning or end of track, or major
obstruction) automatically after the motor is powered up for the first time. Press and hold
the open and close buttons for 10 seconds. The purple LED blinks. The drapery motor
will move the fabric until it finds its close limit and then its open limit.
obstruction) automatically after the motor is powered up for the first time. Press and hold
the open and close buttons for 10 seconds. The purple LED blinks. The drapery motor
will move the fabric until it finds its close limit and then its open limit.
NOTE: Find Limits mode should be entered only after the drapery fabric has been
hung. If it has been entered without the drapery fabric hung it, must be re-run.
hung. If it has been entered without the drapery fabric hung it, must be re-run.
When the drapery limits are not set, the red LED blinks three times, pauses for 1 second,
blinks once, pauses for 5 seconds, and then repeats this code until the limits are set.
blinks once, pauses for 5 seconds, and then repeats this code until the limits are set.
NOTE: After Find Limits mode is completed, the drapery motor runs the drapery fabric
one open and close cycle.
one open and close cycle.
Set Custom Drapery Limits
If the drapery full-open and full-close positions need to be set at different locations from
the default, custom open and closed limits can be set.
If the drapery full-open and full-close positions need to be set at different locations from
the default, custom open and closed limits can be set.
NOTE: After 8 seconds of inactivity, the motor exits Limit Setup mode.
Set the close limit for the drapery.
1. Press and hold the configure button for 4 seconds to enter Limit Setup mode. The
1. Press and hold the configure button for 4 seconds to enter Limit Setup mode. The
LED alternates between amber and green.
2. Press and release the close button to enter close limit setup. The green LED blinks.
3. Use the open and close buttons to move the fabric to its desired position.
4. Press and hold the configure button for 4 seconds. The LED turns solid red to
3. Use the open and close buttons to move the fabric to its desired position.
4. Press and hold the configure button for 4 seconds. The LED turns solid red to
confirm that the lower limit has been successfully set.
NOTE
: If the open limit is not set when the close limit is saved, the motor automatically
enters open limit mode. This typically occurs when the motor direction has been
reversed and both limits are erased.
Set the open limit for the drapery.
1. Press and hold the configure button for 4 seconds to enter Limit Setup mode. The
LED alternates between amber and green.
2. Press and release the open button to enter open limit setup. The amber LED blinks.
3. Use the open and close buttons to set the drapery to its desired position.
4. Press and hold the configure button for 4 seconds. The LED turns solid red to
3. Use the open and close buttons to set the drapery to its desired position.
4. Press and hold the configure button for 4 seconds. The LED turns solid red to
confirm that the upper limit has been successfully set.
NOTE: If the close limit is not set when the open limit is saved, the motor
automatically enters close limit mode. This typically occurs when the motor direction
has been reversed and both limits are erased.
automatically enters close limit mode. This typically occurs when the motor direction
has been reversed and both limits are erased.
Additional Resources
Visit the product page on the Crestron website (www.crestron.com)
for additional information and the latest firmware updates. Use a QR
reader application on your mobile device to scan the QR image.
for additional information and the latest firmware updates. Use a QR
reader application on your mobile device to scan the QR image.
Multicolor LED
Close Push Button
Configure Push Button
Open Push Button
NOTE
: Wireless networks composed predominantly of battery-powered devices may
need additional infiNET EX expanders, such as the CLW-EXPEX or GLA-EXPEX (sold
separately) or other non-battery powered infiNET EX devices, to ensure proper
functionality of the network and battery life for the devices. Refer to the Best Practices
for Installation and Setup of Crestron RF Products (Doc. 6689) for complete system
design guidelines, or contact Crestron True Blue Support for further assistance.
LED
COMMUNICATIONS STATUS
Turns on for 5 seconds
Device is communicating with the control system.
Blinks three times
Device is communicating with the gateway but the
gateway is not communicating with the control system.
gateway is not communicating with the control system.
Blinks twice
Device was previously joined to the network but is not
communicating with the gateway.
Blinks once
Device is not joined to the network.