Digital Security Controls Ltd. 01NB918 Manuel D’Utilisation

The WLS918 Wireless Panic Pendant is a device
designed to transmit an emergency signal from any
location within the range of the alarm system with which
it is used.  Signals from the pendant will be transmitted
whether your alarm system is armed or disarmed.

The pendant can be attached to a lanyard or a belt clip.
The unit is even small and lightweight enough to be
placed in a shirt pocket or tucked inside a purse. The
pendant is also water resistant.

To activate an alarm, press and hold both large outer
buttons for two seconds.

Components of the WLS918
The WLS918 is made up of the following components:

•  Cap - whether it is the tear away cap with attached lanyard (neck strap)

or the cap with attached belt clip.

• Rubber Boot - this boot adds water resistance to the product and

provides a soft grip to be able to easily grab the unit to tear it away or
push the activation buttons

• Clear Plastic Housing - the plastic housing holds the circuit board of

the WLS918 and is put inside the rubber boot

• LED - (Light indication) - the LED is used to indicate various conditions

of the pendant and can be seen through the side of the clear plastic
housing that is not covered by the rubber boot.

• Lithium battery  - the WLS918 is powered by a user replaceable lithium

battery

Tear Away Assembly:
1. The WLS918 comes set up for tear away operation by default. The tear

away cap will already be connected to the clear plastic housing.

2. Remove the cover over the bottom of the clear plastic housing

3. Put the battery into the pendant (please see ‘Replacing the Battery’ for

proper orientation)

4. Insert the clear plastic housing into the rubber boot

©

 2001 Digital Security Controls Ltd.

Printed in Canada  29005932 R001

CAUTION: Changes or modifications not expressly approved by Digital Security Controls Ltd. could void your
authority to use this equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer-
ence in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not occur in a particular installation. If this equip-
ment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:

n

Re-orient the receiving antenna.

n

Increase the separation between the equipment and receiver.

n

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

n

Consult the dealer or an experienced radio/television technician for help.

The user may find the following booklet prepared by the FCC useful: “How to Identify and Resolve Radio/
Television Interference Problems”. This booklet is available from the U.S. Government Printing Office, Wash-
ington D.C. 20402, Stock # 004-000-00345-4.
Digital Security Controls Ltd.  160 Washburn St., Lockport, NY 14094

This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.

Ce dispositif satisfait aux exigences d’Industrie Canada, prescrites dans le document CNR-210. son utilisation
est autorisée seulement aux conditions suivantes: (1) il ne doit pas produire de brouillage et (2) l’utilisateur
du dispositif doit être prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible
de compromettre le fonctionnement du dispositif.

Digital Security Controls Ltd. warrants that for a period of twelve months from the date of
purchase, the product shall be free of defect in materials and workmanship under normal use
and that in fulfilment of any breach of such warranty, Digital Security Controls Ltd. shall, at its
option, repair or replace the defective equipment upon return of the equipment to its repair
depot. This warranty applies only to defects in parts and workmanship and not to damage
incurred in shipping or handling, or damage due to causes beyond the control of Digital
Security Controls Ltd. such as lightning, excessive voltage, mechanical shock, water damage,
or damage arising out of abuse, alteration or improper application of the equipment.

The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of any
and all other warranties, whether expressed or implied and of all other obligations or liabilities
on the part of Digital Security Controls Ltd. This warranty contains the entire warranty. Digital
Security Controls Ltd. neither assumes responsibility for, nor authorizes any other person
purporting to act on its behalf to modify or to change this warranty, nor to assume for it any
other warranty or liability concerning this product.

In no event shall Digital Security Controls Ltd. be liable for any direct, indirect or consequential
damages, loss of anticipated profits, loss of time or any other losses incurred by the buyer in
connection with the purchase, installation or operation or failure of this product.