Climax Technology Co Ltd KPF1 Manuel D’Utilisation

                                                                                                                                                             

     

 

3

& 

If the remote keypad did not sound a long beep, it means the remote keypad did not send the learning 
code to the Control Panel, please press  ＊ key then 7 key again to send the learning code.. 

III.  If the Control Panel receives the learning code, it will display the info accordingly. Refer to the operation 

manual of your Control Panel to complete the learn-in process. 

IV.  After Control Panel receives the signal from remote keypad, it will send an acknowledgement back to remote 

keypad. The remote keypad will then beep 3 times to confirm the acknowledgement has been received. 

I. Press 

and 

both 

# and  ＊  keys together under Normal Operation Mode. Remote Keypad will sound a long 

beep. 

& 

If the remote keypad did not sound a long beep, it means the remote keypad did not send the learning 
code to the Control Panel, please press both # and  ＊  keys together again to send the learning code. 

II.  If the Control Panel receives the learning code, it will display the info accordingly. Refer to the operation 

manual of your Control Panel to complete the learn-in process. 

III.  After Control Panel receives the signal from remote keypad, it will send an acknowledgement back to remote 

keypad. The remote keypad will then beep 3 times to confirm the acknowledgement has been received. 

& 

If remote keypad does not perform 3 beeps, please restart the learning procdeure. 

Step 3. 

After the Remote keypad is learnt-in, put the Control Panel into Walk Test mode, hold the Remote keypad in the 
desired location, and send the learning code to the Control Panel to confirm this location is within the signal range 
of the Control Panel. To send the learning code, either press the  ＊ key then 7 key under Test Mode or press 
both # and  ＊  keys together under Normal Operation Mode. 

Step 4. 

When you are satisfied that the Remote keypad works in the chosen location, you can proceed with mounting the 
Remote keypad following the steps described below (see Mounting Remote keypad). 

Step 5. 

Set your own the KP Pin Code: 

 

I. 

When the keypad is under Test mode, press  ＊ key then 6 key, a long beep will be sound. 

II. Enter 

0000 (default PIN code) 

III. Press 

Χ key, remote keypad sounds a long beep. 

IV.  Enter your new 4-digit code. 
V. Press 

# key, remote keypad sounds a long beep. The new PIN code is enabled. 

Step 6.

 

Press 

 key twice to leave Test mode and the installation is completed. 

z 

I. 

Remove the front cover. 

II.  Using the 2 mounting holes of the back cover as a template, mark off the positions in the most appropriate place. 
III.  Insert the wall plugs if fixing into plaster or brick surface. 
IV.  Screw the Remote keypad onto the wall plugs.   
V.  Replace the front cover.     

z 

You may choose to arm/home arm with/without Control Panel User PIN Code. 

 

Under Test mode, Pressing  ＊  key and then 9 key to enable Arm/ Home with PIN Code function (Default).

¾ 

Enter Arm Mode: Enter any one of Control Panel user code and press 

  key. If panel has no fault and arming is 

successful, the Status Red LED will turn ON alone with a long beep.   

¾ 

Enter Home Mode: Enter any one of Control Panel user cods and 

  key. If panel has no fault and arming is 

successful, the Status Red      LED will flash 4 times alone with 3 beeps. 

¾ 

Return to Disarm Mode: Enter any one of Control Panel user code and 

  key. If disarm is successful, the 

Status Blue LED will turn ON along with 2 beeps.   

 

In the Test mode, Pressing  ＊ key and then 8 key to enable Arm/ Home without PIN Code function

¾ 

Enter Arm Mode: Press 

  key. If panel has no fault and arming is successful, the Status Red LED will turn ON 

alone with one long beep. 

¾ 

Enter Home Mode: Press 

  key. If panel has no fault and arming is successful, the Status Red LED will flash 4 

times alone with 3 beeps. 

¾ 

Return to Disarm Mode: Enter any one of Control Panel user code and 

  Key. If disarm is successful, the 

Status Blue LED will turn ON along with 2 beeps.