HeathCo LLC WLTX205 Manuel D’Utilisation

THANK YOU 

Illustrations may vary from actual unit.

1. 

Please read and understand this entire manual before attempting to assemble, install, 
or operate this sensor.

WARNING: To prevent possible SERIOUS INJURY or DEATH never allow small children near 
batteries. If battery is swallowed, immediately notify a doctor.

NOTE: The range of the wireless doorbell can vary with location, temperature, and battery 
condition.

This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. 
Operation is subject to the following two conditions: (1) this device may not cause 
harmful interference, and (2) this device must accept any interference received, including 
interference that may cause undesired operation.

The user is cautioned that changes or modifications not expressly approved by the party 
responsible for regulatory compliance could void the user’s authority to operate the 
equipment.

 

Use a dry cloth to clean the entry alert.

 

Do not use cleaners or polishes.

 

Do not use any fluids on the entry alert.

Phillips screwdriver

Small flathead screwdriver

Drill

1/16” (1.5 mm) drill bit

Safety goggles

AA

Jumper

1

BB

Screw - small

4

CC

Screw - large

2

DD

Double-sided tape

1

A

Sensor (with preinstalled battery)

1

B

Magnet

2

C

Spacer

2

1 

… Remove the back of the sensor 

(A) by pushing in the tab on the 
bottom with a small screwdriver 
(not included).

… Remove the orange battery tab 

from the sensor (A).

2 

… Press and hold the “SYNC” button 

on the doorbell until the doorbell 
sounds a “Beep-Beep”.

… Press the button inside the sensor 

(A) within 30 seconds of pressing 
the doorbell “SYNC” button.

… Press the button inside the sensor 

again to activate the doorbell and 
ensure the sensor (A) and doorbell 
are synced.

CR2032

SYNC – PRESS
AND RELEASE

.

RESET – HOLD
   10 SECONDS.

TUNE – HOLD
   1 SECOND.

30

3 

… Temporarily position the sensor 

(A) and magnet (B) where they will 
be mounted.

… Move the magnet (B) away from 

the sensor (A) to simulate a door 
being opened. The red LED should 
flash and the doorbell will sound 
“Beep-Beep”.

… If the doorbell does not sound, 

move the doorbell closer to the 
sensor (A) and test again.

NOTE: Do not permanently mount the 
sensor until the sensor and doorbell are 
working properly.

SYNC – PRESS
AND RELEASE

.

RESET – HOLD
   10 SECONDS.

CH

IM

E

 V

O

LU

ME

TUNE – HOLD
   1 SECOND.

FRONT TRANS REAR

4 

The maximum gap between the sensor 
(A) and the magnet (B) is 1/2 in.. The 
arrows on the face of each component 
must be aligned and facing each other.

… Place the sensor (A) on the door 

frame and the magnet (B) beside 
the sensor (A) and ensure the 
arrows are aligned.

… If the magnet (B) is recessed, use 

the spacer (C) to ensure proper 
alignment.

1/2" Maximum

This product is guaranteed to be free of factory defective parts and workmanship for a 
period of 3 years from date of purchase. Purchase receipt is required for all warranty 
claims.

This warranty does not include expendable items (such as light bulbs, batteries, etc.), repair 
service, adjustment and calibration due to misuse, abuse or negligence. Unauthorized 
service or modification of the product or of any furnished component will void this warranty 
in its entirety. This warranty does not include reimbursement for inconvenience, installation, 
setup time, loss of use, unauthorized service, or return shipping charges. This warranty 
is not extended to other equipment and components that a customer uses in conjunction 
with this product.

Contact the Customer Service Team at 1-844-760-3644 or visit www.hamptonbay.com.

Questions, problems, missing parts? 

Before returning to the store, call Hampton Bay Customer Service 

8 a.m. - 5 p.m., CST, Monday - Friday

1-844-760-3644

5 

Use either the small screws (BB) or 
double-sided tape (DD) to mount the 
sensor (A).

… To mount with the small screws 

(BB), remove the back of sensor 
(A) by pushing in the tab on the 
bottom with a small screwdriver. 
Place the sensor (A) back against 
the mounting surface and mark the 
two screw holes. Drill two 1/16 in. 
pilot holes. Attach the sensor (A) 
back with the small screws (BB). 
Tighten securely and snap on the 
front of the sensor (A).

… When attaching the sensor (A) with 

double-sided tape (DD), remove 
paper from both sides of the 
double-sided tape (DD) and apply 
to a clean surface.

6 

Use the small screws (BB) (or the large 
screws (CC) if using the magnet spacer 
(C)) to mount the magnet (B).

… Remove the back of magnet (B) by 

pushing in the tab on the bottom 
of the magnet (B) with a small 
screwdriver.

… Place the magnet (B) back against 

the mounting surface and mark the 
two screw holes.

… Drill two 1/16 in. pilot holes.

… Attach the magnet (B) back with 

the small screws (BB). Tighten 
securely and snap on the front of 
the magnet (B).

 

Type 2032 3V battery (included)

 

The doorbell does not sound.

Make sure batteries are installed according 

to the diagram inside the sensor and 

doorbell (if applicable).

Check the charge of the sensor and doorbell 

batteries (if applicable) and replace if 

necessary.

Make sure the plug-in doorbell has power 

(if applicable).

Sensor and doorbell are not synced. Follow 

Step 2 in the Installation section to sync.

The batteries seem okay, but the 

doorbell does not work after installation.

Metal reduces transmission range. Use 1/4 

in. to 1/2 in. (6 to 13 mm) wood shims to 

move the doorbell or sensor away from the 

metal surface.

Concrete may reduce range. Move the 

doorbell away from the concrete surface.

Locate the doorbell closer to the sensor.

208187-01A

AA

A

A

A

A

B

A

A

B

B

C

C

C

A

B

C

BB

CC

DD

A

BB

BB