Toshiba TEC Corporation HTK10 Manuel D’Utilisation
User manual HANDY TERMINAL
7
☞
☞
☞
☞
NOTE:
HK-K10 handy terminals meet or exceed the requirements of all applicable standards organizations for safe
operation. However, as with any electrical equipment, the best way to ensure safe operation is to read this manual
carefully before performing any type of connection to the handy terminal and operate them according to the agency
guidelines described in the manual.
carefully before performing any type of connection to the handy terminal and operate them according to the agency
guidelines described in the manual.
2.1.
General Safety Rules
CAUTION
•
Use only the components supplied by the manufacturer for the specific HT-K10 being used.
•
Do not attempt to disassemble the HT-K10 handy terminal, as it does not contain parts that can
be repaired by the user. Any tampering will invalidate the warranty.
be repaired by the user. Any tampering will invalidate the warranty.
•
When replacing the battery pack or at the end of the operative life of the HT-K10 handy terminal,
disposal must be performed in compliance with the laws in force in your country.
disposal must be performed in compliance with the laws in force in your country.
•
Before using the devices and the battery packs, read this manual carefully.
•
Do not submerge the HT-K10 handy terminal in liquid products.
2.2.
Power Supply
The power supply for this device has met applicable UL/PSE/KCC/CE/CCC safety requirements.
Please adhere to the following safety instructions per UL guidelines:
Please adhere to the following safety instructions per UL guidelines:
• FAILURE TO FOLLOW THE INSTRUCTIONS OUTLINED MAY LEAD TO SERIOUS PERSONAL
INJURY AND POSSIBLE PROPERTY DAMAGE.
• IMPORTANT SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS.
WARNING
• DANGER – TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, CAREFULLY FOLLOW THESE
INSTRUCTIONS.
Use only Toshiba Tec-approved power supply. Use of a non-Toshiba Tec-approved power supply
may be dangerous and the warranty does not cover damage to the device caused by non-Toshiba
Tec-approved power supply. The package includes international AC plug/s. The AC plug/s must be
plugged in the power supply before the power supply itself is plugged on the wall outlet. The power
supply is intended to be correctly oriented in a vertical or horizontal or floor mount position.
may be dangerous and the warranty does not cover damage to the device caused by non-Toshiba
Tec-approved power supply. The package includes international AC plug/s. The AC plug/s must be
plugged in the power supply before the power supply itself is plugged on the wall outlet. The power
supply is intended to be correctly oriented in a vertical or horizontal or floor mount position.
2.3.
Laser Safety
CAUTION
A Class 2 laser is safe because the blink reflex limit the exposure to no more than 0.25 seconds. It
only applies to visible-light lasers (400–700 nm). Class-2 lasers are limited to 1mW continuous wave,
or more if the emission time is less than 0.25 seconds or if the light is not spatially coherent.
Although staring directly at the laser beam momentarily causes no known biological damage, avoid
staring at the beam as one would with any very strong light source, such as the sun. Avoid that the
laser beam hits the eye of an observer, even through reflective surfaces such as mirrors, etc.
The laser light is visible to the human eye and is emitted from the window indicated in the figure.
only applies to visible-light lasers (400–700 nm). Class-2 lasers are limited to 1mW continuous wave,
or more if the emission time is less than 0.25 seconds or if the light is not spatially coherent.
Although staring directly at the laser beam momentarily causes no known biological damage, avoid
staring at the beam as one would with any very strong light source, such as the sun. Avoid that the
laser beam hits the eye of an observer, even through reflective surfaces such as mirrors, etc.
The laser light is visible to the human eye and is emitted from the window indicated in the figure.