HARRIS CORPORATION M803VTAC Manuel D’Utilisation
WINST-0009 Rev –
WIRELESS SYSTEM BUSINESS UNIT
SUBJECT:
M-803 VTAC Installation Instructions
DATE:
February 19, 2002
Page
1 of 19
COPYRIGHT ©2002
Printed in U.S.A.
M/A-COM
1011 Pawtucket Boulevard
Lowell, MA 01853
1-877-OPENSKY
(1-877-673-6759)
1-877-OPENSKY
O
VERVIEW
This document describes the procedure for installing
the M/A-COM OpenSky
the M/A-COM OpenSky
®
Model VR-803 Vehicular
Tactical Network (V-TAC) in a vehicle, such as an
automobile, truck, or van. This is a general guide only,
and assumes that the installation will be performed by
a professional radio installer.
automobile, truck, or van. This is a general guide only,
and assumes that the installation will be performed by
a professional radio installer.
D
ISCLAIMER
THE INSTALLATION INSTRUCTIONS PROVIDED IN THIS MANUAL ARE FOR
REFERENCE, AND DO NOT CREATE A WARRANTY OF ANY KIND AS TO THE
FUNCTIONALITY OF THE INSTALLED PRODUCT. THE ONLY WARRANTIES
THAT APPLY TO THIS PRODUCT ARE THOSE SET FORTH IN THE SALES
AGREEMENT.
REFERENCE, AND DO NOT CREATE A WARRANTY OF ANY KIND AS TO THE
FUNCTIONALITY OF THE INSTALLED PRODUCT. THE ONLY WARRANTIES
THAT APPLY TO THIS PRODUCT ARE THOSE SET FORTH IN THE SALES
AGREEMENT.
M/A-COM INC. RECOMMENDS THAT BUYER USE ONLY A M/A-COM
AUTHORIZED REPRESENTATIVE TO INSTALL THIS PRODUCT.
AUTHORIZED REPRESENTATIVE TO INSTALL THIS PRODUCT.
THE WARRANTIES PROVIDED TO BUYER UNDER THE TERMS OF SALE
SHALL BE NULL AND VOID IF THIS PRODUCT IS INSTALLED OR SERVICED
IMPROPERLY, AND M/A-COM SHALL HAVE NO FURTHER OBLIGATION TO THE
BUYER FOR ANY DAMAGE CAUSED TO THE PRODUCT OR TO ANY PERSON
OR PERSONAL PROPERTY.
SHALL BE NULL AND VOID IF THIS PRODUCT IS INSTALLED OR SERVICED
IMPROPERLY, AND M/A-COM SHALL HAVE NO FURTHER OBLIGATION TO THE
BUYER FOR ANY DAMAGE CAUSED TO THE PRODUCT OR TO ANY PERSON
OR PERSONAL PROPERTY.
M
ATERIALS
There are three main components to the VR-803 V-TAC: the Full-Duplex Mobile
Radio Unit (MRU); the Vehicular Repeater Base Unit (VRB); and the RF Combiner.
The V-TAC is designed to mount on the floor or on a tray in the trunk or unoccupied
section of a vehicle. The V-TAC is designed to be operated with an externally-
mounted antenna. The Installation Kit (M/A-COM Part #MAMROS0019) needed to
install the V-TAC is described below. The V-TAC is intended to be used with a CH-
103 Control Head with Installation Kit, sold separately.
Radio Unit (MRU); the Vehicular Repeater Base Unit (VRB); and the RF Combiner.
The V-TAC is designed to mount on the floor or on a tray in the trunk or unoccupied
section of a vehicle. The V-TAC is designed to be operated with an externally-
mounted antenna. The Installation Kit (M/A-COM Part #MAMROS0019) needed to
install the V-TAC is described below. The V-TAC is intended to be used with a CH-
103 Control Head with Installation Kit, sold separately.
Table I lists the accessories that are included in the kit. Table II lists additional
options and accessories that may be purchased separately. (Note: The Installation
Kit does not include an antenna. An antenna must be purchased separately, and the
V-TAC may not be installed unless an antenna is to be installed at the same time.)
options and accessories that may be purchased separately. (Note: The Installation
Kit does not include an antenna. An antenna must be purchased separately, and the
V-TAC may not be installed unless an antenna is to be installed at the same time.)