Tyco Safety Products/Sensormatic IDR3000 Manuel D’Utilisation
RFID READER MODEL IDR-3000 INSTALLATION AND SERVICE GUIDE (8200-0222-02, REV. 1/A)
8 of 9
Rebooting the Reader
Use this procedure to recover from a reader error.
1. Disconnect power from the reader.
2. Re-connect reader power.
Wait for at least 60 seconds for the reader to
boot up. The Power/Heartbeat LED is solid
green while the reader boots. When the LED
begins blinking, the boot process is complete.
boot up. The Power/Heartbeat LED is solid
green while the reader boots. When the LED
begins blinking, the boot process is complete.
Using Safe Mode
Use the Safe Mode button on the reader connector
panel to recover from errors that disable the
reader.
panel to recover from errors that disable the
reader.
Safe mode operation restores factory default
settings as follows:
settings as follows:
Firmware Version: ....... factory installed version
UHF (915 MHz) RF Transmit Power: ..............7
HF (13.56 MHz) RF Transmit Power: .............7
IP Address: .......................................10.0.0.101
Subnet Mask: .....................................255.0.0.0
Gateway: ..............................................10.0.0.1
UHF (915 MHz) RF Transmit Power: ..............7
HF (13.56 MHz) RF Transmit Power: .............7
IP Address: .......................................10.0.0.101
Subnet Mask: .....................................255.0.0.0
Gateway: ..............................................10.0.0.1
Although the browser-based interface pages are
displayed in red when operating in Safe mode, the
reader is fully functional. In most cases, the reader
will need to be reconfigured for operation with the
reader application after starting in Safe mode.
displayed in red when operating in Safe mode, the
reader is fully functional. In most cases, the reader
will need to be reconfigured for operation with the
reader application after starting in Safe mode.
1. Disconnect power from the reader.
2. Depress and hold the Safe Mode button while
restoring power to the reader. Keep the Safe
Mode button depressed until the reader boots
completely (the green Power/Heartbeat LED
blinks).
Mode button depressed until the reader boots
completely (the green Power/Heartbeat LED
blinks).
3. Factory-default settings are restored.
4. Use the browser-based interface to configure
4. Use the browser-based interface to configure
the reader for use with your system.
5. Use the Startup Settings page to restart the
reader so the configuration changes take
effect. Once the restart is complete, the reader
is no longer in Safe Mode.
effect. Once the restart is complete, the reader
is no longer in Safe Mode.
Specifications
Electrical
RFID Reader
UHF operating frequency ................... 902–928MHz
HF operating frequency........................... 13.56MHz
Input voltage......................................... 15Vdc, 3.0A
HF operating frequency........................... 13.56MHz
Input voltage......................................... 15Vdc, 3.0A
Separate Power Supply
Input voltage.......... Nominal 100–240Vac, 50/60Hz
Ac line current .......................Nominal 0.5A at 120V
Output voltage .............. Nominal 15Vdc, 4.2A peak
Ac line current .......................Nominal 0.5A at 120V
Output voltage .............. Nominal 15Vdc, 4.2A peak
certified limited power source
Class
2
Environmental
Operating temperature: ....0° to 40°C (32° to 104°F)
Relative humidity:............0 to 90% non-condensing
Relative humidity:............0 to 90% non-condensing
Mechanical
Length ...........................................26.5cm (10.4 in.)
Width .............................................26.6cm (10.4 in.)
Width (including mounting bracket)..30.5cm (12 in.)
Height ................................................3.8cm (1.5 in.)
Weight ..................................................1.4kg (3 lbs)
Width .............................................26.6cm (10.4 in.)
Width (including mounting bracket)..30.5cm (12 in.)
Height ................................................3.8cm (1.5 in.)
Weight ..................................................1.4kg (3 lbs)
Supported Tag Protocols
915 MHz (Alien EPC)
13.56 MHz (Philips I-Code 2, ISO 15693)
13.56 MHz (Philips I-Code 2, ISO 15693)
Safe Mode button
Power/Heartbeat LED