Trans Electric Co. Ltd. SV1100 Manuel D’Utilisation

INTERFERENCE

The RECEIVER can be interfered with an external RF signal. The LED (A/B) of the RECEIVER 
will blink even without pressing a key on the remote control.

If this is the case, please try the below:
1. Try to move the RECEIVER (Reminder: The receiver also transmits IR signals, so try placing 
the receiver so that it also faces your devices.)
2. Reduce the antenna length.

SAFETY PRECAUTIONS

 

•  This product should only be used with the CEC approved AC Power supply    

     

    included in the packaging.

 

•   Inadequately protected or sensitive electronic equipment may be affected    

    

    by the use of this product.

 

•   Before you start, please check whether or not  this product can affect sur-   

     

    rounding equipment.

COMPLIANCE WITH FCC, IC RULES AND 

REGULATIONS

T

his equipment has been tested and found to comply with the limits for a class B digital device, 

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection 

against harmful interference in a residential installation. This equipment generates, uses and radi-

ates radio frequency energy and if not installed and used in accordance with the instructions, may 

cause harmful interference to radio communications. However, there is no guarantee that interfer-

ence will not occur in a particular installation. If this equipment does cause harmful interference 

to radio or television reception, which can be determined by turning the equipment off and on, the 

user is encouraged to try and correct the interference by one or more of the following measures:  
 

•  RE-ORIENT OR RELOCATE THE RECEIVER ANTENNA.

 

•  INCREASE THE SEPARATION BETWEEN THE EQUIPMENT AND THE  

 

 

   RECEIVER.

 

•  CONNECT THE EQUIPMENT INTO AN OUTLET THAT IS DIFFERENT FROM  

 

   THAT TO WHICH THE RECEIVER IS CONNECTED

 

•  CONSULT THE DEALER OR AN EXPERIENCED RADIO/TELEVISION  

 

 

   TECHNICIAN FOR HELP

NOTE:  Changes or modifications not expressly approved by the party responible for compliance 

could void the user’s authority to operate the equipment.
In compliance with the FCC RF exposure requirements, this device and its antenna must not be 

co-located or operating in conjunction with any other antenna or transmitter.
FCC Authorization Label
This device complies with part 15 of the FCC Rules. Operation is subject to the following two con-

ditions:
 

1.  THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND

 

2.  THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,   

 

                    INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION

.

FCC ID #: BY4SV1100      

ADDITIONAL INFORMATION

This product does not have any user-serviceable parts. Opening the case, except for the battery 

cover on the base station, may cause permanent damage to your Remote Extender.
Copyright 2007 by Universal Electronics Inc. No part of this publication may be reproduced, trans-

mitted, transcribed, stored in any retrieval system, or translated to any language, in any form or by 

any means, electronic, mechanical, magnetic, optical, manual, or otherwise, without prior written 

permission of Universal Electronics Inc.

For help via the Internet, visit us at:  www.urcsupport.com/extender

For help via e-mail, contact us at:  cablehelp@ueic.com

STEP 2: SELECTING THE FREqUENCY

Set the Selection Switch (on the back of the RECEIVER) to…

A : 58KHz (Try this setting if your Scientific Atlanta Explorer is not responding)

 

B : 38KHz (Default setting and most common setting for IR controlled devices)

 

C : Sensitivity lower e.g. other equipment using 418 MHz (external

 

      interference). See section: “Interference”.

STEP 3: RECEIvER PLACEMENT

Place the RECEIVER next to the corresponding device(s) you wish to control.

STEP 4: CONNECTING THE IR bLASTER CAbLE

Connect the IR Blaster Cable into the back of the RECEIVER and place the IR Eye(s) on the receiving window 
(IR sensor) of each hidden device you want to control.

STEP 5: APPLYING POWER TO THE RECEIvER

Plug the power adaptor in the wall socket and connect the DC connector to the back of the  

 

RECEIVER. The POWER LED on the top of the RECEIVER will illuminate.

RE-CHARGING THE 2/3 SIzE “AAA” bATTERY

The Remote Control Extender’s receiver is also used to recharge the 2/3 size battery.  The Remote Extender 
comes with 2 rechargeable batteries to ensure your RF remote is always ready for use. If your remote control is 
functioning at a shorter distance than normal (when the LED (A/B) of the RECEIVER does not blink when a key 
on the remote control is being pressed) then the battery needs to be recharged.
1. Remove the (2/3 “AAA” size) battery from your remote control.
2. Place the (2/3 “AAA” size) battery in the compartment located on the bottom
    of the RECEIVER. The LED (BAT) will light up.
3. The LED will switch off as soon as the (2/3 “AAA” size) battery is fully charged.
NOTE: The RF operating range may vary depending on the overall battery charge (e.g. you may have to
replace the “AA”/”AAA” alkaline batteries if the operating range decreases).
Caution: Use only with supplied rechargeable battery. Risk of explosion if battery is
installed by an incorrect type.

INTRODUCTION

The Remote Control Extender is a revolutionary device which will turn virtually any IR (Infra-
red) remote control into an RF (Radio Frequency) remote control.  No longer do your electronic 
devices need to be out in the open for you to control them. Additional benefits of the Remote
Control Extender are:
 

• Send signals through walls and ceilings.

 

• Control Audio and Video devices which are placed out of sight.

 

• RF Transmitter is available wherever the remote control is located.

 

• Installation is as easy as changing a battery.

Please ensure that all of the components below are included and follow the 5 Easy installa-
tion steps below and start enjoying the power of RF control.

THIS PACkAGE CONTAINS:

 

 

1.  Remote Extender Receiver 

 

 

2.  IR Blaster Cable (1.5m, 2m and 3.5m in length)

 

 

3.  “AAA”  RF Transmitter Sleeve

 

 

4.  2 Rechargeable 2/3 Size “AAA” Batteries

 

 

5.  “AA” Battery Sleeve

 

 

STEP 1: INSTALLING THE RF TRANSMITTER AND   

 

    bATTERY

Simply install the RF transmitter instead of one of the “AAA” or “AA” batteries inside your 
remote control.
 
 

1

2

3

4

(x 2)

5

E

Extender Guide2.indd   1

3/20/2007   2:47:03 PM