DEI Headquarters Inc. 7RRRXAD2 Manuel D’Utilisation
6
! Attempted Theft Alert
The system will let you know if there was an attempt made on your vehicle while you were away.
When you remotely disarm, if you hear 3 chirps instead of usual one chirp it means the alarm
sounded in your absence. The system will tell you which trigger or sensor detected the attempt.
When you enter the vehicle, the LED will blink several times, pause, then repeat the blink cycle.
Count the number of blinks in one cycle and refer to the chart that follows:
When you remotely disarm, if you hear 3 chirps instead of usual one chirp it means the alarm
sounded in your absence. The system will tell you which trigger or sensor detected the attempt.
When you enter the vehicle, the LED will blink several times, pause, then repeat the blink cycle.
Count the number of blinks in one cycle and refer to the chart that follows:
Number of LED blinks per cycle after
disarming
Trigger/Sensor Activated
1 blink
Dual-zone impact sensor
2 blinks
Door trigger
3 blinks
Trunk or hood trigger
! How to Interpret the Chirps and Parking Light Flashes
When you press the remote control buttons the system will respond with chirps (unless you have the
chirp muting feature turned on) and flashes the parking lights to the system status. The meaning of
these chirp/flash acknowledgments is as follows
chirp muting feature turned on) and flashes the parking lights to the system status. The meaning of
these chirp/flash acknowledgments is as follows
Number of chirps
and flashes
Meaning
1
Disarming of the alarm
2
Arming of the alarm
2 and then 4
Armed and there is a sensor malfunction (automatically bypassed)
3
Disarmed and there was an intrusion attempt
4
Armed and there is a trigger malfunction (automatically bypassed)
! Selectable Chirp Control
Whenever you wish, you may completely silence the system’s arm/disarm chirps. The short-term and
one-time chirp muting capabilities are especially valuable when parking late at night in a quiet
residential area. You have two choices:
one-time chirp muting capabilities are especially valuable when parking late at night in a quiet
residential area. You have two choices:
! Chirp Canceling: Lets you completely silence the chirps until you wish to restore them. See
User-Programmable Features on page 8.
!
One-Time Remote Chirp Muting: The most simple of all. To remotely arm or disarm the alarm
silently, press button 3
silently, press button 3
User-Programmable Features
Your vehicle security system allows you to set many of its features to your own personal preferences.
We have made the programming procedures very simple: to make a change, you just flick the valet
switch a few times. The system comes the factory with all of its features pre-programmed as noted in
the table on pages 8. To change any of the settings, use the procedure noted. To restore the to its
factory setting, just repeat the procedure:
We have made the programming procedures very simple: to make a change, you just flick the valet
switch a few times. The system comes the factory with all of its features pre-programmed as noted in
the table on pages 8. To change any of the settings, use the procedure noted. To restore the to its
factory setting, just repeat the procedure:
1. Select the feature you wish to program from the table on pages 8. There are 2 stages of
programming. To enter 1st stage insert the ignition key and turn it to the ON position, to enter
2nd stage turn the ignition key from ON position to OFF position.
2nd stage turn the ignition key from ON position to OFF position.
2. Note the number of flicks and chirps associated with that feature.
3. Immediately flick the valet switch back and forth, counting the number of chirps you hear. Stop
3. Immediately flick the valet switch back and forth, counting the number of chirps you hear. Stop
when you reach the number of chirps associated with the feature you wish to program.
4. If noted, do the "secondary action.''
5. After a 3-second pause, you will hear 1-6 chirps, depending on the feature being programmed,
5. After a 3-second pause, you will hear 1-6 chirps, depending on the feature being programmed,
to confirm that you have changed the setting of the feature. Turn the ignition OFF.
6. Repeat steps 1-5 for any other features you wish to program.
Example
To change the passive arming feature from its factory setting of ON to OFF, you would note from the