Tecom Co Ltd USC9330BI Manuel D’Utilisation
Figure 1
USC 9330 Antenna Ports
c.
Seal the DC power connector with waterproof glue or tape.
d.
Connect the black end of the DC cable to the block 1 (0) power output of
the PSE and connect the red end of the DC cable to the block 2 (-48) power
output of the PSE.
the PSE and connect the red end of the DC cable to the block 2 (-48) power
output of the PSE.
Figure 2
PSE and USC 9330 Connections
Step 5
If you are using the power over Ethernet (PoE) option:
a.
Remove the connector cap from the Ethernet connector.
b.
Connect the Ethernet cable to the Ethernet connector on the USC 9330.
c.
Seal the Ethernet connector with waterproof glue or tape.
1
PSE 48V DC input
6
USC 9330 DC power connector
2
PSE power source selector switch
7
USC 9330 RJ45 connector
3
PSE terminal block
8
USC 9330 LED display
4
PSE PoE RJ45 connector
9
USC 9330 reset button
5
PSE WAN Ethernet connector
10
USC 9330 grounding screws
Ant 2
GPS
Ant 1
1
2
3
382244
6
9
8
7
10
1
2
3
4
5
382089
d.
Connect the other end of the Ethernet cable to the PoE port on the PSE.
e.
Connect the WAN port on the PSE to the Internet.
Step 6
Connect two grounding wires to the grounding screws on the USC 9330.
Step 7
Flip the power switch on the PSE to the appropriate location (1 for DC
power and 0 for PoE). The LED on the top of the PSE unit indicates the
power mode: Green: PoE; Blue: DC power.
power and 0 for PoE). The LED on the top of the PSE unit indicates the
power mode: Green: PoE; Blue: DC power.
2
Verify that the USC 9330 is Operational
The LED display is located on the bottom of your USC 9330. Note the color and
activity of the LEDs and refer to this table to diagnose any problems:
activity of the LEDs and refer to this table to diagnose any problems:
If you require assistance installing or operating your small cell, contact customer
support.
support.
Table 1
USC 9330 Status LED Indications
LED Indication
Small Cell State / Action
Power LED (1)
Green
Power is supplied to the unit.
Status LED (2)
Red blink 1 time
in 4 seconds
in 4 seconds
No electrical connection with residential gateway. Verify
connection and verify that the residential gateway is operational
connection and verify that the residential gateway is operational
Red blink 2 times
in 4 seconds
in 4 seconds
No Internet connection—Verify that the residential gateway is
connected to the Internet and is providing service
connected to the Internet and is providing service
Red blink 3 times
in 4 seconds
in 4 seconds
Local interference—phones may be too close to your small cell.
If this problem persists, contact customer support.
If this problem persists, contact customer support.
Red blink 4 times
in 4 seconds
in 4 seconds
Overheating—verify that the small cell is located where there is
proper air flow
proper air flow
Red
Initial boot—wait up to 20 minutes; if still red, perform a reset
Internal fault—Contact customer support
Excessive interference—Verify whether another small cell is
located in close proximity and if so, relocate unit
located in close proximity and if so, relocate unit
Provisioning failure—Contact customer support
Service LED (3)
Fast Green
Initialization or provisioning—Wait for action to complete
Factory reset—Wait up to 20 minutes for action to complete
Green
In service, no calls or data sessions—ready to support calls
Slow Green
In service with active calls or data sessions