Futaba Corporation R7014SB-24G Manuel D’Utilisation

FUTABA CORPORATION

1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan

Phone: +81 475 32 6982, Facsimile: +81 475 32 6983

©FUTABA CORPORATION     2016, 11  (1)

All product and company names mentioned 

herein are the t rademarks or registered 

trademarks of their respective

 owners. 

*Fixed at neutral if a servo is connected to a port other than a usable transmitter channel.
*The telemetry and Extra Voltage ports cannot be used with the FASST system.

 Turn on the receiver.

（Transmitter OFF）

 Press and hold the Link/Mode button for at least 5 seconds. 

 

 When the mode LED begins to blink green/red the button may be released.

 The mode LED should now be blinking red in one of the patterns described by 

the chart below.  ( Default  : FASSTest )

 Each press of the Mode/Link button advances the receiver to the next mode.

 When you reach the mode that you wish to operate in, press and hold the Mode/

Link button for more than 2 seconds.

 Once locked into the correct mode the mode LED will change to a solid color.

 Please cycle the receiver(s) power off and back on again after changing the 

Channel Mode.

 Turn on the receiver.

（Transmitter OFF）

 Press and hold the Link/Mode button for at least 15 seconds.  

 When the mode LED begins to blink red the button may be released.

The mode LED should now be blinking red in one of the patterns described by 
the chart below.  ( Default  : S.BUS )

 Each press of the Mode/Link button advances the receiver to the next mode.

 When you reach the mode that you wish to operate in, press and hold the Mode/

Link button for more than 2 seconds.

 Once locked into the correct mode the mode LED will change to a solid color.

 Please cycle the receiver(s) power off and back on again after changing the 

Channel Mode.

FASSTest is a bidirectional communication system between the R7014SB receiver and FASSTest capable transmitters.  Multiple optional telemetry sensors 

may be connected to the S.BUS2 on the receiver and that data is in turn displayed on the transmitter.

*Please see your transmitters operation manual to configure transmitter to operate with telemetry sensors.

 Bring the transmitter and the receiver close to each other, within 20 inches (half 

meter).

 Turn on the transmitter.  Place the transmitter into the receiver linking mode.

  Turn on the receiver.

 The receiver will wait for the linking process to begin for 2 seconds. Following 

that it will return to the normal operation mode.

 When the link LED of the receiver changes from blinking red to solid green, 

linking is complete. (A link waiting state is ended in 1 second.)

• Refer to the transmitters operation manual for complete details on how to place the 

transmitter into the linking mode.

• If there are many FASSTest systems turned on in close proximity, your receiver might have 

difficulty establishing a link to your transmitter.  This is a rare occurrence.  However, should 
another FASSTest transmitter/receiver be linking at the same time, your receiver could link 
to the wrong transmitter.  This is very dangerous if you do not notice this situation. In order 
to avoid the problem,we strongly recommend you to double check whether your receiver is 
really under control by your transmitter. 

• If the System Type of the transmitter is changed, the receiver will need to be re-linked to the 

transmitter

.

S.BUS2 extends S.BUS and supports bidirectional communication. Sensors 

are connected to the S.BUS2 port.

*Only S.BUS2 capable devices may be connected to the S.BUS2 port.  Standard S.BUS servos 

and gyros should not be connected to the S.BUS2 port.

It connects with the battery for power, etc.

External voltage input cable (CA-RVIN-700) of an option is used. The 

voltage of the battery can be displayed with a transmitter. 

When using a TMA-1 (sold separately), change the settings by the following 

method.

The TMA-1 is a device for viewing the telemetry data on a smartphone or 

tablet.

.

 Switch the receiver to FASSTest system.

.

 Link the transmitter and receiver, and after confirming operation, turn off the 

power.

.

 Turn on the receiver power. (Transmitter power off)

.

 Press the Link/Mode switch for at least 10 seconds.

.

 When the mode LED begins to blink green the button may be released.

. 

The receiver enters the linked with TMA-1 mode, and the LED begins red/

green simultaneous rapid blinking.

.

 Press the TMA-1 link switch until the LED starts to blink and wait for the 

TMA-1 to link.

.

 When TMA-1 linking is complete, the TMA-1 LED changes from red to green 

for a moment.

.

 When linking is complete, turn on the receiver power and check the 

operation of all the devices.

 Bring the transmitter and the receiver close to each other, within 20 inches (half 

meter).

  Turn on the transmitter and receiver.

 Link operation is performed by the Link/Mode switch.

• When using TM-8 module, it's possible to set F/S position (only 3CH).

0 to 1 sec.

1 to 2 sec.

More than 2 sec.

0 sec.

1 sec.

2 sec.

No function

With 

(not included in this set)

To set the F/S 

position(No re-link)

Re-link(ID set) and to 

set the F/S position

No function

Besides 

Re-link(ID set)

*Refer to the instruction manual of the transmitter or module used for a description of the 

linking operation, F/S position setting methods and other details.

The  MPDX-1 can be used with FASSTest by merely setting the corresponding 

transmitter. (Refer to the instruction manual of the corresponding transmitter.) When 

using the MPDX-1 Multi Prop Decoder (sold separately) with the FASST system, 

change the setting by the following method. Enable the MPDX-1 at channels 11 and 

12. (Initial value: OFF) Channels 11 and 12 cannot be used individually for MPDX-

.

 Switch the receiver to the FASST system (Normal or High-speed).

.

 Turn on the receiver power. (Transmitter power off)

.

 Press the Link/Mode switch for at least 10 seconds.

.

 When the mode LED begins to blink green the button may be released.

. 

The receiver enters the multi prop mode and the LED of the current mode 

blinks. (Initial value: OFF)

.

 Each time the switch is pressed, the mode changes.

.

 When the receiver was switched to the desired mode, press the Link/Mode 

switch for at least 2 seconds.

. 

When the mode LED switches to red/green simultaneous rapid blinking, 
mode switching is complete. Release the switch.

.

 When switching is complete, turn on the power. When the power is turned 

on, the receiver switches to the new mode.

When switched, the R7014SB can use the FASST-Multi-ch mode. When the FASST system is used, the telemetry and Extra Voltage ports cannot be used. The 

FASST system has a Normal mode and a High-speed mode. However, in the High-speed mode, analog servos cannot be used at CH1 〜 6.

1 output.The MPDX-1 extends 1 channel to 8 channels. However, since the response 

speed becomes slower and there are functional restrictions, use it at simple switch 

operation and other applications that require numerous channels.