Beijing Smarter Eye Technology Co. Ltd. SMARTEREYEC1 Manuel D’Utilisation
At the speed> 50km / h, when the vehicle is traveling while imposing lines, the
Smarter Eye C1 system give give an alarm, to remind you to go back to the lane,
in the meanwhile, yellow light flickers at the sides of the car body.
Smarter Eye C1 system give give an alarm, to remind you to go back to the lane,
in the meanwhile, yellow light flickers at the sides of the car body.
Lane departure warning - LDW
12
Note: This function can not be disabled or muted, but if Smarter Eye C1 is in standby mode
or the power is turned off, the system will not give a warning.
or the power is turned off, the system will not give a warning.
After the device is successfully connected, insert a hexagon tool into the
groove 1 at the side of the binocular camera, and click the correction function 2
of the camera in the APP, switch the hexagonal tool to adjust the camera angle
with reference to the sample image.
groove 1 at the side of the binocular camera, and click the correction function 2
of the camera in the APP, switch the hexagonal tool to adjust the camera angle
with reference to the sample image.
1
Switch the hexagonal tool, and pay attention to the display of
the mobile phone(refer to the picture below to make adjustment).
the mobile phone(refer to the picture below to make adjustment).
2
*Note: When adjusting the camera, it is necessary to make the horizon of the picture outside
the car shown in the mobile phone and the red line coincide.
Rotate the rotary knob to the bottom, if the horizon and red line still cannot coincide, make
sure that the horizon is close to the red line to the greatest extent.
the car shown in the mobile phone and the red line coincide.
Rotate the rotary knob to the bottom, if the horizon and red line still cannot coincide, make
sure that the horizon is close to the red line to the greatest extent.
Insert the hexagon tool into the
groove at the side of the product.
groove at the side of the product.
Step four
9
Camera Correction
Make sure that the device interface is properly connected, and start the vehicle
to power on the device. If the green indicator light beside the power supply
button is on, it indicates that the connection is correct, if it is not on, please
refer to Figure 6 to check the device display.
to power on the device. If the green indicator light beside the power supply
button is on, it indicates that the connection is correct, if it is not on, please
refer to Figure 6 to check the device display.
Open the SmarterEye app to connect device (scan the QR Code in the manual
to download app if there is no app in your phone), click the device powered
on, and click on the next step as shown in Figure 7.
to download app if there is no app in your phone), click the device powered
on, and click on the next step as shown in Figure 7.
Step two
Step one
green light: normal
No light: the device is not properly connected
or the interface is not connected
or the interface is not connected
red light: standby
7
Figure 6
Figure 7
Step two
As shown in Figure 2 and 3, unmask tear down the double faced adhesive tape
from the device, and then paste the device to the frame at the bottom of the
aid, and then press hard.
from the device, and then paste the device to the frame at the bottom of the
aid, and then press hard.
Note: ensure that there are no vehicles sunshade net and other objects at the location where the
binocular camera is pasted.
binocular camera is pasted.
5
Figure 2
Figure 3
mid
10
20
30
40
50
60
70
80
90
120
110
100
100
130
140
160
150
150
10
20
30
40
50
60
70
80
90
120
110
100
100
130
140
160
150
150
All rights reserved by Beijing Smarter Eye Technology Co,Ltd.
Installation and operating instructions
Please read this installation and operating instruction
carefully and keep it in good care
Smarter Eye ADAS
Standard
3m-60m
40°
Project
Describe
Effective measurement distance
View angle
15FPS
Maximum frame rate
640x480p
resolution ratio
>100mm
Baseline distance
Black and white
Image type
8bit
Data depth
120db
<10%
Dynamic range
Maximum measurement error
<5%
30 m range measurement error
-20°C~ 60°C
service voltage
12V
operating temperature
15
Function Descriptions
At the speed of more than 10km / h, when the vehicle may collide with any
objects (such as cars, pedestrians, bicycles, flower beds, etc.) in front,
Smarter Eye C1 will give the driver an alarm of certain frequency according to
the dangerous level, in the meanwhile, red light flickers at the side of the car
body. FCW gives an alarm up to 2.7 seconds in advance.
objects (such as cars, pedestrians, bicycles, flower beds, etc.) in front,
Smarter Eye C1 will give the driver an alarm of certain frequency according to
the dangerous level, in the meanwhile, red light flickers at the side of the car
body. FCW gives an alarm up to 2.7 seconds in advance.
Forward Collision Warning - FCW
Note : This function can not be disabled or muted, but if Smarter Eye C1 is in standby mode
or the power is turned off , the system will not give a warning.
or the power is turned off , the system will not give a warning.
11
At the speed of 0 - 30km / h, when the vehicle may collide with any objects (such
as cars, pedestrians, bicycles, flower beds, etc.) in front, Smarter Eye C1 will give
the driver an alarm of certain frequency according to the dangerous level, in
the meanwhile, red light flickers at the side of the car body.
as cars, pedestrians, bicycles, flower beds, etc.) in front, Smarter Eye C1 will give
the driver an alarm of certain frequency according to the dangerous level, in
the meanwhile, red light flickers at the side of the car body.
City forward collision warning - CFCW
13
Note: This function can not be disabled or muted, but if Smarter Eye Cl is in standby mode
or the power is turned off, the system will not give a warning.
or the power is turned off, the system will not give a warning.
Other Notes
Product limitations
Limited license
The lane departure warning of the Smarter Eye C1 system is suitable for asphalt
road with clear lane marks.
road with clear lane marks.
Based on the characteristics of this product and technical limitations, omissions,
mistakes or defects occur, when the Smarter Eye C1system is detecting the vehicle,
pedestrian or lane, or giving a warning against potential road traffic danger,
shall not be regarded as the basis for the judgment of unqualified products or
claiming for compensation. Smarter Eye C1 system can't replace the driver to
"observe" road conditions. The driver should keep alert during driving and drive
according to his own observation or knowledge of road conditions. Please be
sure to drive according to the actual traffic conditions and traffic rules. The
Company doesn't assume any responsibility for the traffic accident and the
various losses caused thereby. In addition, the road surface, weather and other
conditions will affect the Smarter Eye C1 system. Covering part or full view of the
binocular camera can cause the function failure or decrease of Smarter Eye C1
system. Please ensure clear vision of the binocular camera.
mistakes or defects occur, when the Smarter Eye C1system is detecting the vehicle,
pedestrian or lane, or giving a warning against potential road traffic danger,
shall not be regarded as the basis for the judgment of unqualified products or
claiming for compensation. Smarter Eye C1 system can't replace the driver to
"observe" road conditions. The driver should keep alert during driving and drive
according to his own observation or knowledge of road conditions. Please be
sure to drive according to the actual traffic conditions and traffic rules. The
Company doesn't assume any responsibility for the traffic accident and the
various losses caused thereby. In addition, the road surface, weather and other
conditions will affect the Smarter Eye C1 system. Covering part or full view of the
binocular camera can cause the function failure or decrease of Smarter Eye C1
system. Please ensure clear vision of the binocular camera.
The software used in this product is the property of Beijing Smarter Eye
Technology Co, Ltd. Beijing Smarter Eye Technology Co, Ltd award purchasers
non-exclusive license of the software, and the purchaser is forbidden to:
Technology Co, Ltd. Beijing Smarter Eye Technology Co, Ltd award purchasers
non-exclusive license of the software, and the purchaser is forbidden to:
(1) modify, refit, change or convert the software used in the product or the
software provided along with the Smarter Eye C1 product, or use it to produce
derivative products, (2) reverse assembly, de-compile, disassemble, etc.to obtain
the source code of software (3) transfer, sublicense, lease, contact, transfer,
disclose the software, etc., or (4) remove the property right of the product or
the corresponding document.
software provided along with the Smarter Eye C1 product, or use it to produce
derivative products, (2) reverse assembly, de-compile, disassemble, etc.to obtain
the source code of software (3) transfer, sublicense, lease, contact, transfer,
disclose the software, etc., or (4) remove the property right of the product or
the corresponding document.
16
Regulatory Notices
America
This equipment has been tested and found to comply with the limits for a Class
B digital device,pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protectionagainst harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This equipment should be installed and operated withminimum distance
20cm between the radiator & your body.
B digital device,pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protectionagainst harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This equipment should be installed and operated withminimum distance
20cm between the radiator & your body.
17
Instructions
Smarter Eye C1 system is activated automatically when you are starting the vehicle
The warning function of Smarter Eye C1 system can be set according to
personal demands
personal demands
1.Don't adjust the binocular camera lens arbitrarily in daily use.
2.Please don't transfer Smarter Eye C1 between different vehicles.
3.Please don't cover the product to ensure normal operation of Smarter Eye Cl
system.Please remove the foreign matters at the front windshield in time if
there are.
2.Please don't transfer Smarter Eye C1 between different vehicles.
3.Please don't cover the product to ensure normal operation of Smarter Eye Cl
system.Please remove the foreign matters at the front windshield in time if
there are.
parameter settings
14
Smarter Eye C1 product can not replace safe and prudent driving.
Please do not change the system settings of Smarter Eye C1 product
during driving!
Please do not change the system settings of Smarter Eye C1 product
during driving!
Warning!
1, Smarter Eye C1 is an advanced driver-assist product that can provide alarms to the
driver in certain potentially dangerous situations. It can not replace the normal
operation of the driver when driving a motor vehicle, nor should the driver be less alert
during driving when using it, but the driver must comply with all the safe driving
standards and practices and comply with traffic rules and laws and regulations.
driver in certain potentially dangerous situations. It can not replace the normal
operation of the driver when driving a motor vehicle, nor should the driver be less alert
during driving when using it, but the driver must comply with all the safe driving
standards and practices and comply with traffic rules and laws and regulations.
2, Smarter Eye C1 system is not an automatic driving system, which can not replace
the operation of the driver or safe driving practice. The driver must not rely on
Smarter Eye C1 to any extent, but remain cautious at any time to ensure the driving
safety and avoid accidents.
the operation of the driver or safe driving practice. The driver must not rely on
Smarter Eye C1 to any extent, but remain cautious at any time to ensure the driving
safety and avoid accidents.
3, Although Smarter Eye C1 has advanced stereo vision software and other specialized
techniques, Smarter Eye C1 can't guarantee complete detection of vehicles, pedestrians, traffic
signs or lanes, thus can not guarantee to provide any sound or visual warning. In addition,
the road face, weather and other conditions will havean impact on the identification and
reaction capacity of the Smarter Eye C1 system. The driver can not rely on Smarter Eye C1 to
ensure safe driving, but comply with safe driving practices.
techniques, Smarter Eye C1 can't guarantee complete detection of vehicles, pedestrians, traffic
signs or lanes, thus can not guarantee to provide any sound or visual warning. In addition,
the road face, weather and other conditions will havean impact on the identification and
reaction capacity of the Smarter Eye C1 system. The driver can not rely on Smarter Eye C1 to
ensure safe driving, but comply with safe driving practices.
Please don't adjust the knob in the binocular camera before reading the installation and
operating instruction of Smarter Eye C1 product carefully. After installing the SmarterEyeC1
product, it is deemed that you have confirmed and agree to operate the Smarter Eye C1
product according to the safety tips and warnings.
operating instruction of Smarter Eye C1 product carefully. After installing the SmarterEyeC1
product, it is deemed that you have confirmed and agree to operate the Smarter Eye C1
product according to the safety tips and warnings.
4. We have made all the efforts to ensure the accuracy of all the information in
this user's manual, but there is possibility of difference caused by non-subjective
negligence. In order to improve the functions or effects of the product, the
equipment specifications and instructions in this guide are to be modified.
You can report the errors or omissions you have found to the technical support
department of Beijing Smarter Eye Technology Co,Ltd.
E-mail: service@smatereye.com
this user's manual, but there is possibility of difference caused by non-subjective
negligence. In order to improve the functions or effects of the product, the
equipment specifications and instructions in this guide are to be modified.
You can report the errors or omissions you have found to the technical support
department of Beijing Smarter Eye Technology Co,Ltd.
E-mail: service@smatereye.com
5,The company reserves the Instruction of Smarter Eye C1 Installation and Operating,
the final interpretation.
the final interpretation.
1
Product Description
Standby/reply
Power interface
Camera regulation mouth
Double faced adhesive tape
Smarter Eye Cl is an advanced driver-assist product that can provide
alarms to the driver in certain potentially dangerous situations.
alarms to the driver in certain potentially dangerous situations.
2
Indicator light
Warning indicator light
Installation Tips
Scan the download to download it
Friendly reminder: Adjust the visual angle of the camera combined with the
mobile client during the installation of Smarter Eye C1, please download
Smarter Eye APP in advance. Please install this product in strict accordance
with the following steps, Our company shall not be liable for product failure,
personal damage and property damage caused by wrong installation of
the product
mobile client during the installation of Smarter Eye C1, please download
Smarter Eye APP in advance. Please install this product in strict accordance
with the following steps, Our company shall not be liable for product failure,
personal damage and property damage caused by wrong installation of
the product
3
Step Three
Plug one end of the OBD plug of power line into the OBD interface 1, and the
other end into the power outlet 2 of Smarter Eye C1
other end into the power outlet 2 of Smarter Eye C1
2
1
Connect the OBD interface of the automobile
Connect the power line
OBD
6
Figure 4
Figure 5
Enter the connection
interface through app.
connection interface.
Step Three
Enter the WIFI use interface to click confirm, and the connected device list pop
up. Click the product name to connect the product (default name: Smarter Eye C1).
The Apple phone users should connect it manually in the mobile phone settings
for the first time use, and input the Wi-Fi password: 12345678.
up. Click the product name to connect the product (default name: Smarter Eye C1).
The Apple phone users should connect it manually in the mobile phone settings
for the first time use, and input the Wi-Fi password: 12345678.
Keep within one meter range of ADAS.
Please wait patiently if it is connected, and delay is permitted for the first
connection.
connection.
If there is no display, make sure that the WIFI of the phone is on. If it is an
Apple phone, please open the permission of WIFI connection.
Apple phone, please open the permission of WIFI connection.
8
Installation completed!
After the angle is adjusted correctly, take the hexagonal tool down and then
the angle of the camera is locked, and the correction is completed.
the angle of the camera is locked, and the correction is completed.
Step Five
Reminder: Please read the product description carefully
before using Smarter Eye C1.
10
Device Installation
Step one
Take out the installation aid in the box, and paste it at the center of the
windshield in the front, (under the original), and keep it horizontally centered
as shown in Figure 1. Make one end of the aid scaleplate hold out against the
juncture of front windshield and top carport. If the aid scaleplate is too long,
it can be cut at identical graduation ( ensure the aid is horizontal).
windshield in the front, (under the original), and keep it horizontally centered
as shown in Figure 1. Make one end of the aid scaleplate hold out against the
juncture of front windshield and top carport. If the aid scaleplate is too long,
it can be cut at identical graduation ( ensure the aid is horizontal).
Please wipe up the windshield in front of the automobile before installation,
and confirm whether you have downloaded Smarter Eye app. The angle of
ADAS camera shall be adjusted combined with Smarter Eye app.
and confirm whether you have downloaded Smarter Eye app. The angle of
ADAS camera shall be adjusted combined with Smarter Eye app.
Note: The position of the aid should be in the middle of the front windshield of the car. Refer
to the position of the rear view mirror bracket when pasting it, to ensure that the aid is level
and not slant.
Make sure that the mounting bracket at the bottom of the aid is within the wiping range of
the windscreen wiper when pasting the aid.
Ensure that the sunshade net at the rear of rear view mirror is not within the mounting frame
at the bottom of the aid when pasting the aid.
You can cut out the aid scaleplate according to your own demand, and ensure that the
remaining two numerical values of dividing rulers at the left and right are the same (ensure
that the aid is level)
to the position of the rear view mirror bracket when pasting it, to ensure that the aid is level
and not slant.
Make sure that the mounting bracket at the bottom of the aid is within the wiping range of
the windscreen wiper when pasting the aid.
Ensure that the sunshade net at the rear of rear view mirror is not within the mounting frame
at the bottom of the aid when pasting the aid.
You can cut out the aid scaleplate according to your own demand, and ensure that the
remaining two numerical values of dividing rulers at the left and right are the same (ensure
that the aid is level)
4
Figure 1
Smarter Eye C1