Zopoise Technology Co. Ltd HIBAY1A-SENSOR Manuel D’Utilisation
ಁޙ
໎ճ
ಌۢ
ٝྼ
γᅹܤ
ಌՇ
ଛᅹ
ఐ
γޚ ҉ ำߑٗ؟γޚ
ஆᆓ
ఐ
͑ੋ
ྂγޚ
२
ᄷ२
Αै
٫ྚ
ԛྚ
ы
ۜ
ॸۜ
ᄹెࢳޏďᅉᄽĐပຫ٤ഓ
=RSRLVH7HFKQRORJ\=KX]KRX&2/7'
Jഀᄜ
ഊੜೠ
=36*&:)
:,<)
ζӦΩۜ
ޏ೬ྑௐġ
cϫᄩġJഀᄜĢ
cٝྼঠёġJഀᄜďഀੋĐ
kӷkნྚkͧᅭĢ
cઝఘํӐēরēڶԘރୣ
Ϣ॥ຣເē૦͑ჾ௲ĢჾֱੋĢ
cюଶѤӊġ PPĢ
cཞౄӦ۱ġ.d
cϫᄩġJഀᄜĢ
cٝྼঠёġJഀᄜďഀੋĐ
kӷkნྚkͧᅭĢ
cઝఘํӐēরēڶԘރୣ
Ϣ॥ຣເē૦͑ჾ௲ĢჾֱੋĢ
cюଶѤӊġ PPĢ
cཞౄӦ۱ġ.d
Competitor Product Comparison
Confidential – for internal use only
IMPORTANT: READ CAREFULLY BEFORE INSTALLING THE FIXTURE. RETAIN FOR FUTURE REFERENCE.
GENERAL: Upon receipt of the fixture, thoroughly inspect for any freight damage which should be brought to the attention of the delivery carrier.
GENERAL: Upon receipt of the fixture, thoroughly inspect for any freight damage which should be brought to the attention of the delivery carrier.
INSTALLATION:
1.
Remove housing (A) along with hardware bag from packaging.
2.
Remove refractor (B)/reflector (C) from packaging.
3.
Attach the housing to refractor/reflector by using 3 screws (from hardware bag). (See
Fig. 1)
Fig. 1)
4.
Attach hook (from hardware bag) into threaded opening in the top of the housing.
(See Fig. 2)
(See Fig. 2)
5.
Hook high bay fixture to eyelet or chain (provided by others).
6.
Secure the set screw on hook by tightening. (See Fig. 3)
7.
Attach safety cable (provided by others) through hole in top of housing. (See Fig.4)
8.
Connect the incoming electrical wires to the set of power wires black to black (hot),
white to white (neutral) and green to green (ground). (See Wiring Diagram)
white to white (neutral) and green to green (ground). (See Wiring Diagram)
9.
Installation is now complete. Turn on the power at circuit breaker or fuse box then
turn the light switch to power the fixture.
turn the light switch to power the fixture.
SAFETY PRECAUTIONS:
A
A
B
C
A
A
B
C
Complete Fixture with Refractor
Complete Fixture with Reflector
100W Housing
200W Housing
Refractor
Reflector
Screws for
Refractor
Refractor
Figure 1
Safety
cable
location
cable
location
Safety
cable
location
cable
location
Threaded opening (G ½)
Hook
Hook captive
screw
screw
Hook set
screw
screw
Hook
Figure 2
Figure 3
Figure 4
Wiring Diagram
A
300W Housing
Competitor Product Comparison
Confidential – for internal use only
CLEANING AND MAINTENANCE
To maintain the fixture efficacy occasional cleaning of the outer lens surface may be needed.
Use a mild soap or detergent, which is essentially neutral pH (pH approximately 6 to 8), nonabrasive, and
which contains no chlorinated or aromatic hydrocarbons.
Wash thoroughly, using a soft cloth.
Rinse with clean, cold water and wipe dry.
Use a mild soap or detergent, which is essentially neutral pH (pH approximately 6 to 8), nonabrasive, and
which contains no chlorinated or aromatic hydrocarbons.
Wash thoroughly, using a soft cloth.
Rinse with clean, cold water and wipe dry.
TROUBLE SHOOTING CHECKLIST: If luminaire does not work
– Check your power source.
– Check electrical connections.
– Check electrical connections.
E22477
CHANGING THE SENSOR SETTINGS (Remote sold separately):
This fixture is compatible with 0-10V output dimming controls (please reference Dimmable Compatibility
List LEDLUM012). To get to 0% light output (OFF) it is necessary to disconnect the input power from the
LED drivers. Connect sensor or wall dimmer to dimming wires on driver. (See Wiring Diagram 2)
List LEDLUM012). To get to 0% light output (OFF) it is necessary to disconnect the input power from the
LED drivers. Connect sensor or wall dimmer to dimming wires on driver. (See Wiring Diagram 2)
ADDING A SENSOR OR WALL DIMMER (Provided by others):
Wiring Diagram 2
1. Use infrared remote (NAED 71758) to change the sensor settings. (See Fig. 1A)
2. Sensor will automatically start in Auto Mode. Press “On” to start the manual programming mode.
2. Sensor will automatically start in Auto Mode. Press “On” to start the manual programming mode.
(Please note: After “On” is pressed and no settings are set, “Auto” mode will resume after 20
minutes.)
minutes.)
Default Settings:
3. To select the default mode, press the “Reset” button. If one setting must be changed in the default mode,
then select the desired setting, press button and wait for the sensor to flash 3 times and turn off.
Sensitivity: 100%
Stand-by time: 5 minutes
Lux: Disabled
Dimming level: 30%
Dimming time: 60 min
Stand-by time: 5 minutes
Lux: Disabled
Dimming level: 30%
Dimming time: 60 min
4. Turn fixture on and settings will remain saved until changed.
To change Default Settings please refer to document
With power failure, fixture will remain with latest settings
Remote cannot store settings except for default (“Reset Button”)
CR205 battery included
With power failure, fixture will remain with latest settings
Remote cannot store settings except for default (“Reset Button”)
CR205 battery included
Competitor Product Comparison
Confidential – for internal use only
ADDING A BOTTOM LENS (Sold separately):
1. Remove bottom lens and clamp screw from packaging
2. Place lens over opening of refractor and place clamp over lens and refractor rim. Place screw through hole in clamp and tighten clamp to secure.
2. Place lens over opening of refractor and place clamp over lens and refractor rim. Place screw through hole in clamp and tighten clamp to secure.
(See Fig. 6)
Clamp
Figure 5
Figure 6