Grizzly Ears LLC GRIZZLYEARS46 Manuel D’Utilisation
Erect headset and place
them into the cochlea
Slightly rotate headset until it firm
Make the headset to cochlear edge tightly.
Maintenance
Quick reference & trouble shooting
Do not use abrasive cleaning solvents to clean the headset.
Do not allow the headset to touch with any sharp objects as this will cause
scratching and damage
Please keep headset away from high-temperature, humidity and dust.
www.grizzly-ears.com YouTube for set-up or trouble shooting
•
•
•
•
1. No need to power off earbuds just put back into charging case
and close.
2. When taking out earbuds from charging case, earbuds will
automatically connect to devise once it’s already sync to your
device. If charging case needs to be charged…earbuds might
have powered off to save power. Just press down both earbuds
2-3 seconds to until you hear power on.
3. If one earbud is only working press and hold the earbud not
working for 2 seconds until you hear power on and then both
earbuds should sync to device
4. If you’re in amplify press once to exit amplify mode before
placing back into charging case
5. If you only want amplify with shot compression and not
Bluetooth then turn off Bluetooth on your device and double
press earbuds to activate amplify with shot compression. If you
turn Bluetooth off on your device...it will give you longer battery
charge up to 5 hours for amplify/shot compression.
6. You must be in amplify mode in order for shot compression to
work.
7. If you’re using lanyard & you want to just hang earbuds around
neck...make sure you power off conserve battery. Push down for
6-8 seconds until you hear power off. To turn power on press
both earbuds 2-3 seconds at same time until you hear power on.
8. If you hear beeping in one earbud...it means one earbuds is off
and trying to sync to the other earbud. Press the earbud that’s
not beeping for 2-3 seconds until you hear power on.
9. You only have to push 1 earbud for 6-8 seconds if you’re
powering off earbuds.
Remove the Earplugs
Pinch the earplug and rotate back & forth gently until earplug has
been removed off the shaft.
Wearing
Reconnection
The earphones will reconnect to the device when you’re back into
the working range after distance break.
Once the earhones are paired to the device, it will reconnect
automatically on second time usage.
Note:
If it cannot reconnect to your device, please turn on the device
pairing function, select the Grizzly Ears 46 to connect again.
If you still cannot do the reconnection, please delete the pairing
record on your device, do the set up again.
Reset
Off-stage earphones, press both earphones and hold for 5-8
seconds until you see pink light or heard short 3 beeps. (operation
to delete the internal pairing)
LED: blue – red – pink
Voice: power on – power off – beep beep beep
Turn on the earphones, wait for 5-10 seconds to let the earphones
pair by themselves (operation to build up the internal pairing).
LED: blue – red/blue – blue – red/blue just on right earphone
Voice: power on – b – b … - left connected/right connected -
pairing
Earplugs
Note: Recommended to use a larger size earplug when shooting
for better Hearing Protection.
XS
S
M
L
NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for
help
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.