GUANGDONG GDA Valve Technology.Co.Ltd GH03-C Manuel D’Utilisation
Press and hold the SET key until the desired set temperature is
reached.(By pressing and holding the set key the LCD screen set
numbers will increase from 45ºto 99ºthen restart over at 45º).Next
release the SET key.The LCD screen will display the set temperature
for 3 seconds and the LCD screen will flash the set temperature for
3seconds,then the LCD screen will default to display the room
temperature.
reached.(By pressing and holding the set key the LCD screen set
numbers will increase from 45ºto 99ºthen restart over at 45º).Next
release the SET key.The LCD screen will display the set temperature
for 3 seconds and the LCD screen will flash the set temperature for
3seconds,then the LCD screen will default to display the room
temperature.
TO CHANGE THE SET TEMPERATURE
Press and hold the SET key until the desired set temperature is
reached.(By pressing and holding the set key the LCD screen set
numbers will increase from 45ºto 99ºthen restart over at 45º)Next
release the SET key.The LCD screen will display the set temperature
for 3 seconds,then will flash the set temperature for 3 seconds,then
the LCD screen will default to display the room temperature.
reached.(By pressing and holding the set key the LCD screen set
numbers will increase from 45ºto 99ºthen restart over at 45º)Next
release the SET key.The LCD screen will display the set temperature
for 3 seconds,then will flash the set temperature for 3 seconds,then
the LCD screen will default to display the room temperature.
Press the MODE key to disengage the thermo mode.The word ROOM
on the LCD screen will not show when the thermo is not in operation.
on the LCD screen will not show when the thermo is not in operation.
NOTE:The highest SET temperature is 99ºFahrenheit(32ºCelsius) and
the lowest temperature is(45ºFahrenheit(6ºCelsius)
the lowest temperature is(45ºFahrenheit(6ºCelsius)
OPERATIONAL NOTES:
The Thermo Feature on the transmitter operates the appliance whenever the ROOM TEMPERATURE varies a
certain number of degrees from the SET TEMPERATURE.This variation is called the “SWING”or
TEMPERATURE DIFFERENTIAL.The normal operating cycle of an appliance may be 25-30 times per hour
depending on how well the room or home is insulated from the cold or drafts.The factory setting for the”swing
number”is 2.This represents a temperature variation of +/-2ºF(1ºC)between SET temperature and ROOM
temperature,which determines when the fireplace will be activated.
certain number of degrees from the SET TEMPERATURE.This variation is called the “SWING”or
TEMPERATURE DIFFERENTIAL.The normal operating cycle of an appliance may be 25-30 times per hour
depending on how well the room or home is insulated from the cold or drafts.The factory setting for the”swing
number”is 2.This represents a temperature variation of +/-2ºF(1ºC)between SET temperature and ROOM
temperature,which determines when the fireplace will be activated.
The transmitter has ON and OFF manual functions that are activated by pressing either button on the face of
the transmitter.When a button on the transmitter is pressed the word ON or OF will appear on the LCD screen
to show while the signal is being sent.Upon initial use,there may be a delay of three seconds before the remote
receiver will respond to the transmitter.This is part of the system’s design
the transmitter.When a button on the transmitter is pressed the word ON or OF will appear on the LCD screen
to show while the signal is being sent.Upon initial use,there may be a delay of three seconds before the remote
receiver will respond to the transmitter.This is part of the system’s design
POWER SETTING-GH03-R
The electronics in the remote control system have the capability of”powering”two different types of DC-
powered components.If any operational problems are noted,contact Customer Service.
powered components.If any operational problems are noted,contact Customer Service.
The RECEIVER comes from the factory programmed to provide pulse DC voltage(5.5VDC to 6.3VDC)to a
latching solenoid.
latching solenoid.