RadioShack Corporation 3201258T Manuel D’Utilisation

Set TALK-MUTE-OFF switch to TALK. Then turn the 

audio source and receiver volume up to the desired 

level. The READY indicator light displays indicating that 

the microphone signals are within range of the receiver.

OFF to TALK, use MUTE. 

Press POWER on the receiver to turn it on. The 

POWER indicator lights up. �ully e�tend the antennae.

�ully e�tend the antennae. 

Set the volume on your PA amplifier or other audio 

source to a minimum level. Then turn power on.

�requency ............. 169.505MHz, 170.245MHz or 171.905MHz

Operating Range ............................................ 200 feet (Typical)

�requency Response ..........................................120---13000Hz

R� Power ........................................................................ 10dBm

Sensitivity............................................ 106 dB SPL at 7KHz �M

Power Source ................................................Two AA Batteries

Sensitivity with S/N 20dB ....................................................1uV

S/N Ratio at 1mV R� Input .................................................75dB

Image Rejection .................................................................55dB

Line Output .....................................................................510mV 

Microphone Output ..........................................................10mV

Power Requirement ................................................ AC Adapter

Warning: Modifying, tampering with, or adjusting this unit, or replacing 

any transmitter component (crystal, semiconductor, etc.) may result in a 

violation of the FCC rules.

Consult your local RadioShack store or an experienced radio/TV technician 

for help.

If you cannot eliminate the interference, the FCC requires that you stop 

using your microphone system. Changes or modifications not expressly 

approved by RadioShack may cause interference and void the user’s 

authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to 

the condition that this device may not cause harmful interference.
This wireless microphone system complies with Part 90 of the FCC Rules. 

There are three frequencies available for the system. You must obtain a 

license for each frequency you plan to use before operating your system. 

One license can include both frequencies. Visit http://wireless.fcc.gov/uls/, 

or call your local FCC office to apply for your license. Your ability to obtain 

a license will depend on how you plan to use the system.
For RF exposure

“IMPORTANT NOTE: To comply with the FCC RF exposure compliance 

requirements, no change to the antenna or the device is permitted. Any 

change to the antenna or the device could result in the system exceeding 

the RF exposure requirements.”
For devices less than 200mW ERP
SAFETY INFORMATION

Your wireless microphone contains a low power transmitter. When the EUT 

is powered on, it sends out radio frequency (RF) signals. In August 1996, 

the Federal Communications Commissions (FCC) adopted RF exposure 

guidelines with safety levels for wireless devices.
IMPORTANT

To maintain compliance with the FCC’s RF exposure guidelines, hold the 

transmitter and antenna at least 1 inch (2.5 centimetres) from your face 

and speak in a normal voice, with the antenna pointed up and away from 

the face. Ensure that the antenna is at least 1 inch (2.5 centimetres) from 

your body when you are using your wireless microphone. 
Use only the supplied antenna. Unauthorized antennas, modifications, 

or attachments could damage the transmitter and may violate FCC 

regulations.

©2006.

RadioShack Corporation. 

All rights reserved. 

RadioShack and 

RadioShack.com are trademarks 

used by 

RadioShack Corporation.

32-1258

04A06 

AO0262AAA1 

Printed in China 

This product is warranted by RadioShack against manufacturing defects 

in material and workmanship under normal use for one (1) year from the 

date of purchase from RadioShack company-owned stores and authorized 

RadioShack franchisees and dealers. For complete warranty details and 

exclusions, check with your local RadioShack store.
RadioShack Customer Relations 

300 RadioShack Circle, Fort Worth, TX 76102 

 

04/04

Please read this user’s guide before installing, setting up 

and using your new product.

www.radioshack.com

Connect your 

receiver to the 

input jack on 

your amplifier 

using the LINE 

jack.

(Optional) 

Connect your 

receiver to 

your amplifier 

with the 

jack.

Plug the AC 

adapter into 

an outlet.

Rotate to limit the background noise and 

control the transmitting distance. To increase 

the transmitting distance, rotate it to MIN.

POWER indicator

Replace the batteries 

when light is off.

POWER indicator

READY indicator

POWER button

Rotate to adjust your microphone’s 

volume.

NOTES

Unscrew the microphone grille and 

remove the battery cover. Insert two 

AA batteries with correct polarity. 

Then replace the battery cover and the 

microphone grille.

Set the volume to a minimum level and plug in the 

AC adapter. Then, using a shielded audio cable (not

using a shielded audio cable (not 

included), connect the LINE jack on your receiver 

to the input jack on your amplifier, or other device.� 

Optionally, or if the input jack is in use, you can

if the input jack is in use, you can 

connect using the MICROPHONE jacks on your 

receiver and amplifier with a 1/4” audio cable (not 

included).

NOTE