Shanghai Senben Lighting Technology Company HUNHE120 Manuel D’Utilisation
and painted with polyester on the outer surface.
9.The tensile strength of the aluminum alloy enclosure is no less than 120MPa and content of
magnesium and titanium of the enclosure is no more than 7.5% of the total content, the enclosure is
anti-corrosion. See Figure 2 for the light structure.
10.The flame proof electrical box shall subjected to specified internal explosion without any damage,
the flame proof threads will provide a flame path to cooldown the enclosure in case of internal
explosion.
11.Increased safety chamber is used as a reflector, it’s
casted by aluminum plate with anodizing on the internal
surface and polycarbonate coated on the external surface.
Light with 120W and 150W illuminant has assistant
reflectors.
12.The maximum surface temperature of the enclosure
shall be less than 80℃ without dust layer.
13.Flat toughed glass or polycarbonate prisma can be
adopted as transparent plate.
14.Transparent plate and illuminant enclosure are fixed
with aluminum alloy made hoop, it’s endurable and
reliable with good oxidation resistance.
15.Rubber sealing rings are adopted between flame proof
electrical box and increased safety chamber, these will
ensure the good ingress protection performance.
16.Electromagnetic induction illuminant equipped special
ballast with high steady frequency and high steady power,
make the light is available to work under a wide range of
voltage with long service life, it will also ease visual
fatigue.
17.The light is provided with cable entries(compression
nut type) with rubber sealing rings inside for user’s
convenience to wiring and cable sealing.
18.Bulk type terminals make wiring reliable.
19.The light can be installed in pipe suspending type, ceiling type, wall mounting type, guard pole
type and flange pole type. See Figure 2 for installation instructions.
9.The tensile strength of the aluminum alloy enclosure is no less than 120MPa and content of
magnesium and titanium of the enclosure is no more than 7.5% of the total content, the enclosure is
anti-corrosion. See Figure 2 for the light structure.
10.The flame proof electrical box shall subjected to specified internal explosion without any damage,
the flame proof threads will provide a flame path to cooldown the enclosure in case of internal
explosion.
11.Increased safety chamber is used as a reflector, it’s
casted by aluminum plate with anodizing on the internal
surface and polycarbonate coated on the external surface.
Light with 120W and 150W illuminant has assistant
reflectors.
12.The maximum surface temperature of the enclosure
shall be less than 80℃ without dust layer.
13.Flat toughed glass or polycarbonate prisma can be
adopted as transparent plate.
14.Transparent plate and illuminant enclosure are fixed
with aluminum alloy made hoop, it’s endurable and
reliable with good oxidation resistance.
15.Rubber sealing rings are adopted between flame proof
electrical box and increased safety chamber, these will
ensure the good ingress protection performance.
16.Electromagnetic induction illuminant equipped special
ballast with high steady frequency and high steady power,
make the light is available to work under a wide range of
voltage with long service life, it will also ease visual
fatigue.
17.The light is provided with cable entries(compression
nut type) with rubber sealing rings inside for user’s
convenience to wiring and cable sealing.
18.Bulk type terminals make wiring reliable.
19.The light can be installed in pipe suspending type, ceiling type, wall mounting type, guard pole
type and flange pole type. See Figure 2 for installation instructions.
3. Directions
1. Luminarie should be avoided to endure the impact of the external force, in order to avoid to affect the
performance of explosion-proof and dust-proof
2. Luminarie's inlet wire guide wire should be multistrand core wires.
performance of explosion-proof and dust-proof
2. Luminarie's inlet wire guide wire should be multistrand core wires.
3. The luminarie has the Internal and external grounding screws, pls ground according to the regulation
when installation.
when installation.
4. Pls close the power and operate first when change the ballast and light source, then ensure the workers’
safety.
safety.
Before mount, user should check the all of connecting bolt were screwed well, in case impact the
luminaire's protection performance and safety
luminaire's protection performance and safety
6. User should check the luminaire's electric whether it is in good condition regularly. In order to ensure the
luminaire's efficiency, safety and life-span, user should clean the luminaire's surface
7. In order to ensure explosion proof lamp work and safety regularly, the serviceman should be trained
professionally, then can install and maintance. Not-professional person should not open the fixture, and do
not demount any fastening parts.
luminaire's efficiency, safety and life-span, user should clean the luminaire's surface
7. In order to ensure explosion proof lamp work and safety regularly, the serviceman should be trained
professionally, then can install and maintance. Not-professional person should not open the fixture, and do
not demount any fastening parts.
11
10
1
3
2
4
9
8
7
5
6
1-illuminant enclosure 2-illuminant 3-assistant
reflector 4-electrical box 5-junction box 6-
compression nuts cable entry 7-user terminal 8-
electrical box cover 9-ballast 10-transparent
plate 11-hoop
reflector 4-electrical box 5-junction box 6-
compression nuts cable entry 7-user terminal 8-
electrical box cover 9-ballast 10-transparent
plate 11-hoop
Figure2