ZONDA HOBBY TECHNOLOGIES ELECTRONIC LIMITED HK0003 Manuel D’Utilisation
8.Trouble Shooting
6
Trouble Description
Possible reason
Solution
Can not turn on the
transmitter
transmitter
Missing battery or voltage
Changing battery and re-charging the battery
Turn on the transmitter,
Buzzer
have noise but can not
turn on the transmitter.
Buzzer
have noise but can not
turn on the transmitter.
1)Throttle position has not push down to the lowest position.
2)Other functions can not go back to default "0" position.
2)Other functions can not go back to default "0" position.
1)Please check the throttle stick position, push down the stick at
the lowest position.
2)Please check all the functions button or switch, and adjust the
value back to "0" position
the lowest position.
2)Please check all the functions button or switch, and adjust the
value back to "0" position
Can not connect with
the receiver normally
the receiver normally
1)When turn on the transmitter, user press the binding
button carelessly
2)Is there any metal or other material suround with you
3)The helicopter is not charging normally
button carelessly
2)Is there any metal or other material suround with you
3)The helicopter is not charging normally
Remote control area
has not achieve the
standard
has not achieve the
standard
The receiver antenna must have a distance with other
electronic wire (at least 20mm)
electronic wire (at least 20mm)
1)Is it the helicopter type not correct?
2)Is it Servo not working properly?
3)Is there any strong frequency jammed, affecting the
transmission quality?
2)Is it Servo not working properly?
3)Is there any strong frequency jammed, affecting the
transmission quality?
1)Please make sure the transmitter setting is matching
with the correct helicopter model
2)Please make sure the servo is working properly
3)Please make sure there is no any big frequency device
in the area. It is include wireless router or frequency tower
with the correct helicopter model
2)Please make sure the servo is working properly
3)Please make sure there is no any big frequency device
in the area. It is include wireless router or frequency tower
Under the operation, LED
is flashing unexpectedily,
the Buzzer have noise
contiuously.
is flashing unexpectedily,
the Buzzer have noise
contiuously.
The battery power is very low (Lower than 20%)
or connection error, occur the alarm.
or connection error, occur the alarm.
Please check the battery stick tight, and then check the
battery power. Charging the battery on time and replace
the battery if necessary.
battery power. Charging the battery on time and replace
the battery if necessary.
1)Is the receiver antenna mix with the other device wire
together?
2)Is the receiver antenna loose or damage?
together?
2)Is the receiver antenna loose or damage?
Remote control can not
operate properly
operate properly
1)Please press the binding button to re-binding the transmitter
2)Please stay in a flat area without heavy or many metals
surounded area
3)Please check the receiver battery power and connector is
connected correctly
2)Please stay in a flat area without heavy or many metals
surounded area
3)Please check the receiver battery power and connector is
connected correctly
FCC ID: 2AAB6-HK0003
Item Number:
Zonda Hobby Technologies Electronic Ltd
Warning: Changes or modifications to this unit not expressly approved by theparty responsible for compliance
could void the user s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfe-
rence in a residential installation. This equipment generates, uses and can radiate radiofrequency energy and,
if not installed and used in accordance with theinstructions, may cause harmful interference to radio communi-
cations.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
To comply with FCC s RF radiation exposure limits for general population/uncontrolled exposure, this device
must be operated only in hands with a separation distance of at least 20 cm from its antenna to the body. In add-
ition it must not be collocated or operating in conjunction with any other antenna or transmitter.
Item Number:
Zonda Hobby Technologies Electronic Ltd
Warning: Changes or modifications to this unit not expressly approved by theparty responsible for compliance
could void the user s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfe-
rence in a residential installation. This equipment generates, uses and can radiate radiofrequency energy and,
if not installed and used in accordance with theinstructions, may cause harmful interference to radio communi-
cations.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
To comply with FCC s RF radiation exposure limits for general population/uncontrolled exposure, this device
must be operated only in hands with a separation distance of at least 20 cm from its antenna to the body. In add-
ition it must not be collocated or operating in conjunction with any other antenna or transmitter.
GWY005451
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED
BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING
TO THE INSTRUCTIONS
RISK OF EXPLOSION IF BATTERY IS REPLACED
BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING
TO THE INSTRUCTIONS
Correct Disposal of this product. This marking indicates that this product should not be disposed with
other household wastes throughout the EU. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To
return your used device, please use the return and collection systems or contact the retailer where the product
was purchased. They can take this product for environmental safe recycling.
other household wastes throughout the EU. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To
return your used device, please use the return and collection systems or contact the retailer where the product
was purchased. They can take this product for environmental safe recycling.
Hereby, ZONDA HOBBY TECHNOLOGIES ELECTRONIC LIMITED, declares that this
is in compliance with the essential requirements and other relevant provisions of
Directive 1999/5/EC
GWY005451