Shenzhen Jetson Electronic Technologies Co. Ltd JET-M2-400C Manuel D’Utilisation
4
TYRE GUARD
3
TYRE GUARD
Tyre alignment mode
Hold down the “
” and “
” buttons simultaneously on the monitor for 5 seconds to enter
tyre alignment mode, and press either “
” or “
” button to select the specific tyre that
needs to be aligned.
Screw a sensor to the tyre valve stem and the current pressure will be displayed against
the corresponding flashing tyre icon on the screen. Once the tyre is aligned successfully
the green light appears on the monitor. The red LED light appears on the monitor if the
sensor hasn’t been aligned and “- - -” also appears on the monitor.
the corresponding flashing tyre icon on the screen. Once the tyre is aligned successfully
the green light appears on the monitor. The red LED light appears on the monitor if the
sensor hasn’t been aligned and “- - -” also appears on the monitor.
Note: If the sensor is to be removed from one valve and fitted to another valve, you must
delete the current setting on the monitor and realign this sensor to the new tyre. To delete
an aligned sensor from a tyre, hold down the SET button for 5 seconds.
delete the current setting on the monitor and realign this sensor to the new tyre. To delete
an aligned sensor from a tyre, hold down the SET button for 5 seconds.
When you exit the alignment mode, by again holding down the “
” and “
”, buttons
simultaneously on the monitor for 5 seconds to check the pressures and temperatures,
the monitor will indicate the data of the selected tyre. Click through to ensure all tyre
pressures and temperature details are in accordance with your requirements. After your
checks are completed, the backlight will go out and the monitor will indicate the tyre
pressure of the selected tyre.
the monitor will indicate the data of the selected tyre. Click through to ensure all tyre
pressures and temperature details are in accordance with your requirements. After your
checks are completed, the backlight will go out and the monitor will indicate the tyre
pressure of the selected tyre.
Installation of the Sensor and anti-theft device
It’s very simple to install the sensors. Screw a sensor
to each tyre valve stem as the picture shows.
to each tyre valve stem as the picture shows.
Note:
1. Always install the sensor when the tyre is cold
2. Please check each tyre valve is not damaged.
3. Check to ensure there are no leaks and the sensors
are firmly secured to each tyre valve.
are firmly secured to each tyre valve.
A
Valve
Anti-theft
Devce
Devce
Driver
c
The sensor has an anti theft ring to prevent the
sensors being stolen. Firstly, place the
anti_ theft ring over the valve stem,with one
side of the inner hexagon facing out, place the
hexagon head of the sensor into the inner
hexagon and then screw down the sensor;
finally, place the inner hexagon screws of the
anti- theft device and tighten with the key
provided. Please refer to the right graphics
A, B and C when installing the rings.
sensors being stolen. Firstly, place the
anti_ theft ring over the valve stem,with one
side of the inner hexagon facing out, place the
hexagon head of the sensor into the inner
hexagon and then screw down the sensor;
finally, place the inner hexagon screws of the
anti- theft device and tighten with the key
provided. Please refer to the right graphics
A, B and C when installing the rings.
Standard Pressure Setting
Hold down SET button for 5 seconds to exit the Standard Pressure Setting mode.
Hold down the set button of the monitor for 5 seconds to enter into the setting
mode, as the right graphic shows. press“ ”or “ ”button to set the required
pressure,and then quickly press the SET button to scroll through to the next the
tyre and repeat this sequence to set the remaining tyres.
mode, as the right graphic shows. press“ ”or “ ”button to set the required
pressure,and then quickly press the SET button to scroll through to the next the
tyre and repeat this sequence to set the remaining tyres.
Examination of the Tyre Condition
The monitor indicates " --- " when a specific sensor' s alignment is lost from
the monitor, as graphic A shows. refer to Tyre Alignment Mode on page 3 to
realign sensor.
the monitor, as graphic A shows. refer to Tyre Alignment Mode on page 3 to
realign sensor.
The monitor will indicate the " noS " signal whenever a sensor is either out of
range or may be faulty, as graphic B shows.
range or may be faulty, as graphic B shows.
Installation of the Monitor
The monitor can be mounted using the pedestal or brackets supplied. The monitor can
be fixed to a suitable surface in the vehicle, sun visor, dashboard etc. It has a build-in
lithium battery or you may wish to use a power source from within the vehicle’s power
socket to charge or operate the monitor.
be fixed to a suitable surface in the vehicle, sun visor, dashboard etc. It has a build-in
lithium battery or you may wish to use a power source from within the vehicle’s power
socket to charge or operate the monitor.