Cinch Systems Inc RF-MDWS-ITI-S Manuel D’Utilisation
Mini DW Sensor—Installation Instructions
Micro Wireless Sensor and Accessories
1 - RF-MDWS Sensor 1- Mounting Tape 1 - RF-MDWS Magnet 2 - Batteries
( 2- 3VDC CR 2032)
Instructions
Tamper
switch
switch
Doc # I-RF-MDWS Rev. A Sep 2014
Installation
1. Remove the transmitter’s cover by pressing in on the
1. Remove the transmitter’s cover by pressing in on the
small rectangular latch on the end of the cover and
lift up
lift up
2. Mount the sensor base directly to the surface using
the mounting tape provided. Make sure to align the
mounting tape with the tamper pull put area on the
bottom of the sensor to insure proper tamper opera-
tion.
mounting tape with the tamper pull put area on the
bottom of the sensor to insure proper tamper opera-
tion.
3. Mount the magnet next to the sensor and align the
magnet with the mark on the side of the sensor,
using the mounting tape provided
using the mounting tape provided
4. Remove the battery isolator tabs from both batteries
on the sensor
5. Replace the cover on the transmitter
6. Enroll the senor into the control panel according the
6. Enroll the senor into the control panel according the
instructions
Note: Mounting the transmitter onto metal surfaces may
impact the effective range of the transmitter
Cover
Latch
Latch
Cover
Latch
Latch
Tamper
Base
Base
Note: Battery Safety
Observe polarity when inserting
replacement batteries to avoid
damaging the sensor.
Risk of fire, burns and explosion.
Do not recharge, disassemble, burn
or expose batteries to tempera-
tures above 100C (212F)
Dispose of used batteries properly
and in accordance with all local
laws
Keep batteries away from children
replacement batteries to avoid
damaging the sensor.
Risk of fire, burns and explosion.
Do not recharge, disassemble, burn
or expose batteries to tempera-
tures above 100C (212F)
Dispose of used batteries properly
and in accordance with all local
laws
Keep batteries away from children
Batteries
Mini DW Sensor—Installation Instructions
Micro Wireless Sensor and Accessories
1 - RF-MDWS Sensor 1- Mounting Tape 1 - RF-MDWS Magnet 2 - Batteries
( 2- 3VDC CR 2032)
Instructions
Tamper
switch
switch
Doc # I-RF-MDWS Rev. A Sep 2014
Installation
1. Remove the transmitter’s cover by pressing in on the
1. Remove the transmitter’s cover by pressing in on the
small rectangular latch on the end of the cover and
lift up
lift up
2. Mount the sensor base directly to the surface using
the mounting tape provided. Make sure to align the
mounting tape with the tamper pull put area on the
bottom of the sensor to insure proper tamper opera-
tion.
mounting tape with the tamper pull put area on the
bottom of the sensor to insure proper tamper opera-
tion.
3. Mount the magnet next to the sensor and align the
magnet with the mark on the side of the sensor,
using the mounting tape provided
using the mounting tape provided
4. Remove the battery isolator tabs from both batteries
on the sensor
5. Replace the cover on the transmitter
6. Enroll the senor into the control panel according the
6. Enroll the senor into the control panel according the
instructions
Note: Mounting the transmitter onto metal surfaces may
impact the effective range of the transmitter
Cover
Latch
Latch
Cover
Latch
Latch
Tamper
Base
Base
Note: Battery Safety
Observe polarity when inserting
replacement batteries to avoid
damaging the sensor.
Risk of fire, burns and explosion.
Do not recharge, disassemble, burn
or expose batteries to tempera-
tures above 100C (212F)
Dispose of used batteries properly
and in accordance with all local
laws
Keep batteries away from children
replacement batteries to avoid
damaging the sensor.
Risk of fire, burns and explosion.
Do not recharge, disassemble, burn
or expose batteries to tempera-
tures above 100C (212F)
Dispose of used batteries properly
and in accordance with all local
laws
Keep batteries away from children
Batteries