KMP Taiwan Co. Ltd 63100114 Manuel D’Utilisation
GARAGE AMOUR OPERATION INSTRUCTION G2
Syncing your new Remote Control to your Control Module
1. Press and release the “Learning Switch” located on the right side of the Control Module. You may
1. Press and release the “Learning Switch” located on the right side of the Control Module. You may
need a pen to push this.
2. Indicator on the Module will turn Yellow and will beep once.
3. Press and release the “0” button on your new Remote. The indicator on the Module will turn off and
3. Press and release the “0” button on your new Remote. The indicator on the Module will turn off and
will beep once. This confirms proper programing of the Remote Control to the Control Module. Note
that this must be done within 10 seconds or the system will exit.
that this must be done within 10 seconds or the system will exit.
4. Up to 10 Remotes can be programmed to one Control Module.
Program your Password
1. Press and release the “Learning Switch” on the Control Module.
2. Press and release the “#” button on the Remote Control you wish to program that has already been
1. Press and release the “Learning Switch” on the Control Module.
2. Press and release the “#” button on the Remote Control you wish to program that has already been
synced with your Control Module and Indicator will turn Red.
3. Enter your 3 to 8 digit code (using number 0 to 9) then press enter.
4. Indicator will turn off and beep twice to confirm entry.
5. To change password simply repeat.
Using Remote to Open your Door Among Three Doors
4. Indicator will turn off and beep twice to confirm entry.
5. To change password simply repeat.
Using Remote to Open your Door Among Three Doors
1. Input your new 3 to 8 digit code.
2. Press enter.
3. Input door no.1 or no.2 or no.3 at the same time and press Enter
4. Buzzer will beep twice, indicator will turn green and door will open.
5. Press Enter to reverse.
2. Press enter.
3. Input door no.1 or no.2 or no.3 at the same time and press Enter
4. Buzzer will beep twice, indicator will turn green and door will open.
5. Press Enter to reverse.
Note: For security purpose, 5 incorrect entries will result in a long warning beep and require
resynchronization.
Using Remote to Open your Two Doors Among Three Doors At The Same Time
6. Input your new 3 to 8 digit code.
resynchronization.
Using Remote to Open your Two Doors Among Three Doors At The Same Time
6. Input your new 3 to 8 digit code.
7. Press enter.
8. Input door no.1 no.2 or no.2 no.3 or no.1 no.3 or no.1 no.2 no.3 and then press Enter
8. Input door no.1 no.2 or no.2 no.3 or no.1 no.3 or no.1 no.2 no.3 and then press Enter
9. Buzzer will beep twice, indicator will turn green and door will open.
10. Press Enter to reverse.
Note: For security purpose, 5 incorrect entries will result in a long warning beep and require
resynchronization.
10. Press Enter to reverse.
Note: For security purpose, 5 incorrect entries will result in a long warning beep and require
resynchronization.
You might enter any series of digits prior to your real code so as long as your last inputted digits are correct,
then enter and the door will open.
Pressing Enter again within 15 seconds will stop the operation of the opening of your garage door. You
may hit Enter repeatedly to open and stop the opening. Press the “#” button to stop this function.
may hit Enter repeatedly to open and stop the opening. Press the “#” button to stop this function.
To Erase Password from Remote Control Memory
1. Press and hold “Learning Switch” for 3 seconds.
1. Press and hold “Learning Switch” for 3 seconds.
2. Buzzer will beep 3 times, indicator light will turn off.
The Button on Receiver:
The button on the receiver is only functional for the door no. 1.