Skspruce Technologies Inc. WIM1200-20-A Manuel D’Utilisation
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or
transmitter.
This device is restricted to indoor use.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
The module is limited to OEM installation ONLY.
This module is intended for OEM integrators under the following conditions:
1.
1.
This module is restricted to installation in products for use only in mobile and fixed applications.
2.
The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm
from all persons.
3.
The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or
transmitter.
4.
OEM integrator has be limited the operation channels in channel 1-11 for 2.4GHz band.
The OEM integrator is still responsible for
1.
1.
ensuring that the end-user has no manual instructions to remove or install module
2.
the FCC compliance requirement of the end product, which integrates this module.
3.
Appropriate measurements (e.g. 15 B compliance) and if applicable additional equipment authorizations
(e.g. Verification, Doc) of the host device to be addressed by the integrator/manufacturer.
4.
The separate approval is required for all other operating configurations, including portable configurations
with respect to Part 2.1093 and different antenna configurations
The user manual of the end product should include
1.
The user manual of the end product should include
1.
Any changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate this equipment.
2.
the restriction of operating this device in indoor could void the user’s authority to operate the equipment.
3.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or
transmitter.
4.
This equipment should be installed and operated with minimum distance 20cm between the radiator & your
body.
5.
The FCC part 15.19 statement: This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Label of the end product:
Label of the end product:
The final end product must be labeled in a visible area with the following
" Contains TX FCC ID: 2ACKD-WIM1200-20-A ".
The end product shall bear the following 15.19 statement: This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired operation.
If the labeling area is considered too small and therefore it is impractical (smaller than the palm of the hand) to
display the compliance statement, then the statement may be placed in the user manual or product packaging.