Kenxen Electronic Limited. SDV180 Manuel D’Utilisation

     Power on: Press the Power button for seconds and red 
       light turns on
      Power off: Press the Power button for seconds again and 
       the red light will flash until turn off

     Wi-Fi on: Press the Wi-Fi button, blue light turns on and it 
       will flash when data transfer.
       Wi-Fi off: Press the Wi-Fi button again, blue light will turn off.

     Press the Recording button, it will start recording when red light
       flash; press the Recording button again, the recording stop.  (In 
       case of no card, full or any error, the red light will flash fast)

 

       Connecting with USB cable & A/C adaptor, the Red light will 
       turn on and recharging start; the Red light will turn off when 
       recharging completed.

      Press this button and the camera will reset.

1). Wi-Fi On / Off
2). Power On / Off
3). Recording button
4). TF card port

5). Micro-USB port
6). Reset button
7). Lens

Lens: F2.0 FOV 190°

  Video format: 1920*1080(1080p)  30FPS
     Storage: MicroSDHC
     Input Current: 1.5A
     Input Voltage: 5V
     Operating Temperature: - 20°~+70C°
    Power: 1.8 Watt 

1. User Manual

     

    

Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment  

This  device  can  be  recharging  via  USB  cable  &  A/C  adaptor  or 
power  bank  and  it  is  recommended  to  use  rating  5V  /  1.5A  or 
above for this operation

  Smartphone system should be Android 5.0 or iOS 8 & above. 

       Android users can download the App Ezzy360 from Google play 
       store and iOS users can download the App Ezzy360 from App Store. 

This product is in compliance with Directive 2011/65/EU of the European
Parliament and of the Council of 8 June 2011, on the restriction of the use 
of certain hazardous substances in electrical equipment.  

6

7

5

4

1

2

3

5
4

2

1

3

A/C 

adaptor

Power 

bank

NOTE:  This equipment has been tested and found to comply with the limits 
for a Class B digital device, pursuant to Part 15 of the FCC Rules.  These limits 
are designed to provide reasonable protection against harmful interference in 
a residential installation.  This equipment generates, uses and can radiate 
radio frequency energy and, if not installed and used in accordance with the 
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular 
installation.  If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off 
and on, the user is encouraged to try to correct the interference by one or 
more of the following measures:
o Reorient or relocate the receiving antenna.
o Increase the separation between the equipment and receiver.
o Connect the equipment into an outlet on a circuit different from that to 
which the        receiver is connected.
o Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules.   Operation is subject to 
the following two conditions:  
(1) this device may not cause harmful interference, and 
(2) this device must accept any interference received,   including interference 
that may cause undesired operation.

ｅｓｔａｂｌｉｓｈｅｄ　ｂｙ　ｔｈｅ　Ｆｅｄｅｒａｌ　Ｃｏｍｍｕｎｉｃａｔｉｏｎｓ　Ｃｏｍｍｉｓｓｉｏｎ　（ＵＳＡ）．

Ｔｈｅ　ＳＡＲ　ｌｉｍｉｔ　ｏｆ　ＵＳＡ　（ＦＣＣ）　ｉｓ　１．６　Ｗ／ｋｇ　ａｖｅｒａｇｅｄ　ｏｖｅｒ　ｏｎｅ　ｇｒａｍ　ｏｆ　ｔｉｓｓｕｅ．　Ｔｈｉｓ

ｐｒｏｄｕｃｔ　ｈａｓ　ａｌｓｏ　ｂｅｅｎ　ｔｅｓｔｅｄ　ａｇａｉｎｓｔ　ｔｈｉｓ　ＳＡＲ　ｌｉｍｉｔｅｄ．

Ｔｈｉｓ　ｄｅｖｉｃｅ　ｉｓ　ａｌｓｏ　ｄｅｓｉｇｎｅｄ　ｔｏ　ｍｅｅｔ　ｔｈｅ　ｒｅｑｕｉｒｅｍｅｎｔｓ　ｆｏｒ　ｅｘｐｏｓｕｒｅ　ｔｏ　ｒａｄｉｏ　ｗａｖｅｓ

(The USB port is only for battery charging and

not use for PC connection to transfer data.)