CHINA ELECTRONIC TECHNOLOGY CO. LTD NW-BS07 Manuel D’Utilisation

English

SELF CAMERA MONOPOD SPECIFICATION：

1.Bluetooth V3.0, low power consumption, highspeed without delay;

2.Compatible with IOS and Android dual system;

3 automatic default system, no need to switch Android or IOS system;

4.Do not need to install the APP;

5.Distance:10m;

6.Working frequency: 2.402-2.480GHz,

work mode: GFSK;

7.Working current: 1mA

(primary dormancy 0.5mA)

8.Working voltage: 3 V to 4.2 V

9.Working temperature: - 10-55 degrees;

SELF CAMERA MONOPOD

1. CELLPHONE HOLDER

2. STELL MONOPOD

3. CAMERA KEY

4. FOCUS ENARGE KEY

5. FOCUS NARROW KEY

6. POWER KEY

7. 1/4 SCREW

8. Micro USB Charging

9. Power LED

My selftimer Use methed：

5 3 2

1.Open:short press the power switch,

LED lights up, after 1second, the green

LED lights down;

2.Paired / online:

2.1 Press the Camera key for 2 seconds, the

green LED is flashing , the device is pairing mode;

2.2 Open mobile phone search Bluetooth device,

the bluetooth device is self timer-03;

2.3 Click the self timer-03 link of Bluetooth devices;Wait for 8 seconds, when the green LED is constant

Cellphone Fixed Mount

Flexible Pipe

Remote Joystick

Illustration 1

Use method 1:

1. Screw up flexible pipe

with cellphone fixed mount.

2. Insert the flexible pipe to

remote joystick and fixture.

3. Put the cellphone connecting

the fiexed mount.

Illustration 2

Remote Joystick

Sleeping mode:

1.When the device is not used for 5
minutes, the device is sleeping mode, the
bluetooth is discon-necting.

2. Short press the camera key, the device cance the

dormant, and connecting the phone automaticlly.

3. When the cellphone bluetooth and the device is

disconnecting, connection again, short press the

camera key, the device is connecting automaticlly.

10.Work humidity: 10% to 70%;

11.Battery: 100mA Lithium batteries；

IN THE BOX

1. SELF CAMERA MONOPOD*1

2. USER Manual*1

3. Micro-USB Charging Cable

4. Cellphone Holder

lighting, they are paring successful;

3.Photos: light press the photo keys, photo is complete.

4:4 Focal length setting: long press "+" button to enlarge the focal length,

long press "-" key to narrow the focus;

5.Power oﬀ: press 3 seconds power key;

6.Charging: The MIRCO USB interface is at the bottom of the selftimer, when you charge it,

and the red LED is lighting.

Illustration 1

Use method 2:

Method Two

Screw up the cellphone fiexed mount with tripod

Put the cellphone connecting the fiexed mount.

Illustration 2

Not include the tripod

Note: my selftimer support the iOS5.0
above and the android2.3.6above.

Because the android is open source
system,so a little phoner/tablet models
may not support remote cameras.

FCC Statement

This equipment has been tested and
found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to
provide reasonable protection against
harmful interference in a residential
installation. This equipment generates
uses and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may
cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur
in a particular installation. If this
equipment does cause harmful
interference to radio or television
reception, which can be determined by
turning the equipment off and on, the user
is encouraged to try to correct the

interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and
receiver.
-- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician
for help.

Changes or modifications not expressly approved by the
party responsible for compliance could void the user's
authority to operate the equipment.

This device complies with part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference,
and (2) this device must accept any
interference received, including
interference that may cause undesired
operation.