Valeport Ltd 0804IDU Manuel D’Utilisation
HydrINS 2 / HydrINS 2 Mini flow meter
Installation Manual
Page 57 / 83
9 Technical Characteristics:
9.1 Hydrins II Probe
Measurement range
Two-way, from 0.02 m/s to 5 m/s, limited only by the stability and stiffness of the probe.
Fluid with conductivity of at least 20 µS/cm.
Fluid with conductivity of at least 20 µS/cm.
Precision
Point speed measurement: at mean or smoothed speed: ±2% if V
≥
10cm/s and ±2mm/s with respect to the
reading if V < 10cm/s.
Mean speed and volume: refer to the ISO 7145-1982 standard.
Mean speed and volume: refer to the ISO 7145-1982 standard.
Units
mm, metres, litres, Megalitres, m
3
, feet, ft
3
, ImpGal, USGal, MegaImpGal,
MegaUSGal, seconds, minutes, hours, days.
Electrical power
On internal lithium batteries with four-year battery life (for one measurement per minute). Ten-year option.
Sensor identity and parameters
Internal calibration, serial number, calibration date, file history.
Calibration
Performed at the factory on hydraulic bench connected to COFRAC calibration standards.
Self-test
Via the embedded electronics in accordance with OIML R49 Type P.
Internal parameters
Volume totalizer in non-volatile memory. Negative / Positive / Net volume
Several modifiable parameters (unit, period, insertion factor, etc.).
Several modifiable parameters (unit, period, insertion factor, etc.).
Outputs
RS 232
Configurable for: point speed, mean speed, instantaneous flow rate, volume totalisers.
Pulses
Two pulse outputs, opto-isolated open collectors Maximum frequency: 50 Hz Pulse width: 10ms - 28V 50 mA
maximum - Max. impedance 35 Ohms - Typical capacitance: 25 pF
maximum - Max. impedance 35 Ohms - Typical capacitance: 25 pF
Possibility: one positive flow channel and one negative flow channel, or one flow channel and one channel for the
flow direction.
flow direction.
External connector
10-pin waterproof military connector.
Software
Interfaced with Winfluid.
Operating temperature
Electronics: -20 to +60°C, Inserted part: unfrozen water at +60°C.
Maximum operating pressure
20 bars - 1/8" BSP pressure fitting, Quickfit connector included.
Waterproofing
IP68/NEMA6 for immersion at 10 m for 72 hours (with fittings connected).
Installation
On insertion valve (ball valve) 1" BSP internal free bore diameter 25 mm (1"NPT as an option). Probe anti-
ejection chain.
ejection chain.
Insertion length
300, 500, 700 and 1000 mm.
Dimensions
Sensor diameter: 22 mm. Stem diameter: 19 mm.
Head diameter: 130 mm x 100 mm high.
Weight
< 3.5 kg.
Materials used
Inserted part:
316 stainless - grey PVC, WRAS approval No. 0307501.
Nitrile seals, WRAS approval No. 0470NBR70.
Nitrile seals, WRAS approval No. 0470NBR70.
ACS certification
External part: Stainless 316 - Bronze CZ 121 - Reinforced ABS housing.
External part: Stainless 316 - Bronze CZ 121 - Reinforced ABS housing.
Guarantee:
36 months.
Metrological certification
Calibrated using electromagnetic flow meters (100 and 200 mm) calibrated according to COFRAC
procedures.
Gauge
Measurement of pipe inside diameters. Standard length 500/700/900.
Other lengths available as options.
Other lengths available as options.