Reliance Worldwide Corporation UFMT1000 Manuel D’Utilisation
1. Wi-Fi Connection
log in to account
connect to meter
Go to: www.dashboard.soneter.net
User Name:
Password:
1
Plug in your meter to any standard wall outlet that is close to your wireless router.
The blue LED will be solid. If not, push the button 5 times in less than 5 seconds.
On a computer or mobile device, open Wi-Fi settings and connect to the network
named “Soneter_XXXX” where the X’s are replaced by the 4 characters below.
The blue LED will be solid. If not, push the button 5 times in less than 5 seconds.
On a computer or mobile device, open Wi-Fi settings and connect to the network
named “Soneter_XXXX” where the X’s are replaced by the 4 characters below.
Soneter_
___ ___ ___ ___
If the network doesn’t appear, move closer to the meter or press the push button 5
times in less than 5 seconds. The unit will reset and the blue LED will become solid.
The network should now appear.
times in less than 5 seconds. The unit will reset and the blue LED will become solid.
The network should now appear.
Setup using an iPhone or iPad is not yet supported, for best experience please
either use a PC, Mac computer, or Anroid phone to connect to Wi-Fi. After Wi-Fi
is connected, you will be able to log in to your account with any device.
either use a PC, Mac computer, or Anroid phone to connect to Wi-Fi. After Wi-Fi
is connected, you will be able to log in to your account with any device.
connect meter to home wi-fi
2
When connected to the Soneter network, open a browser page. Enter the URL
http://10.10.100.254. Fill in your network SSID and Password, and click Connect.
http://10.10.100.254. Fill in your network SSID and Password, and click Connect.
When you see a message saying “rebooting”, close this page and rejoin your
home Wi-Fi network. The blue LED will flash intermittently for about a minute.
When continually single flashing, the meter is connected. If it is continually double
flashing after a minute, press the push button 5 times in under 5 seconds. The
blue LED will become solid and reset its network. Repeat steps 1 and 2.
home Wi-Fi network. The blue LED will flash intermittently for about a minute.
When continually single flashing, the meter is connected. If it is continually double
flashing after a minute, press the push button 5 times in under 5 seconds. The
blue LED will become solid and reset its network. Repeat steps 1 and 2.
Single flash pattern - Wireless connection is functioning normally
4 sec
4 sec
4 sec
2. install location
3. install meter
4. calibration
Find your main water shutoff valve. Look for a spot near the shutoff valve that
has at least 5 inches of straight exposed pipe. The meter does not need to be
immediately adjacent to the shutoff valve.
has at least 5 inches of straight exposed pipe. The meter does not need to be
immediately adjacent to the shutoff valve.
The location should be on the main water line before it branches off to outdoor,
your water heater, ect. The meter works on 3/4’’ and 1’’ copper and cpvc pipe.
Wait until step 3 to install the meter, but place it on the chosen pipe to ensure
it fits and the sensors can contact the pipe surface.
your water heater, ect. The meter works on 3/4’’ and 1’’ copper and cpvc pipe.
Wait until step 3 to install the meter, but place it on the chosen pipe to ensure
it fits and the sensors can contact the pipe surface.
The selected location must allow the meter to plug in to a standard wall outlet.
You may need an extension cord.
You may need an extension cord.
Plug in the meter. The blue LED will flash intermittently for about a minute after
plugging in. When it is continuously single flashing, it is connected.
plugging in. When it is continuously single flashing, it is connected.
If the blue LED is continuously double flashing after a minute or so, you may
need to move closer to your router or away from obstacles. (HVAC ducts, ect.)
need to move closer to your router or away from obstacles. (HVAC ducts, ect.)
plug in & verify wi-fi
choose location on pipe
1
2
1. Clean Pipe
Use the included emery
cloth to remove dust,
paint or other particles.
cloth to remove dust,
paint or other particles.
2. Apply Grease
Using half of the tube,
apply dime-sized drops
of grease to the specified
sensor areas on the back
of the meter.
apply dime-sized drops
of grease to the specified
sensor areas on the back
of the meter.
3. Set Zip Ties
Loosely fasten two zip ties
around the pipe. This will
help make securing the
meter easier.
around the pipe. This will
help make securing the
meter easier.
4. Mount Meter
5. Secure Zip Ties
Press the meter onto the
pipe between the two
zip ties.
pipe between the two
zip ties.
Be very careful not to twist
or slide the meter as this
may displace the grease.
or slide the meter as this
may displace the grease.
Without shifting the meter,
move the zip ties over the
tabs.
move the zip ties over the
tabs.
Hold the meter against the
pipe and tighten the zip ties
over the tabs so they are as
tight as possible.
pipe and tighten the zip ties
over the tabs so they are as
tight as possible.
When the green LED is double-flashing, this means it is ready for calibration.
If it is still single-flashing, the signal is not strong enough to pass through the
pipe. Cut off the zip ties, use a paper towel to wipe the grease off the pipe and
bottom of the meter. Repeat steps 1 - 5 in Section 3, making sure the grease is
applied properly and zip ties are fully tightened.
pipe. Cut off the zip ties, use a paper towel to wipe the grease off the pipe and
bottom of the meter. Repeat steps 1 - 5 in Section 3, making sure the grease is
applied properly and zip ties are fully tightened.
When the set zero is complete, the green LED will triple flash. Turn your main
water shutoff valve back on and run any water fixture for a few seconds. This
allows the meter to know which way the water is flowing.
water shutoff valve back on and run any water fixture for a few seconds. This
allows the meter to know which way the water is flowing.
After flushing a toilet or running a sink, the green LED should become solid,
indicating the meter has completed the setup process. If the green LED is
still triple flashing, the meter may not be installed on the main water line.
indicating the meter has completed the setup process. If the green LED is
still triple flashing, the meter may not be installed on the main water line.
You should now be able to log in to your account and verify you are able to
see live water flow.
see live water flow.
4 sec
4 sec
4 sec
Turn off your main water shutoff valve, or be sure there is absolutely no water
running. Once there is no water flowing, hold down the
running. Once there is no water flowing, hold down the
push button for 5-8
seconds to run a set zero. The green LED will blink rapidly for about 30 seconds
during this process. When successful, it will proceed to a triple flash.
during this process. When successful, it will proceed to a triple flash.
If the green LED continues double flashing, be sure there is no water flow in the
pipe and repeat the set zero process. Continue until triple flash.
pipe and repeat the set zero process. Continue until triple flash.
set flow direction
run set zero
1
2
3
Only use the included grease tube to install the meter. Do not
use any other substance, or the pipe material may be affected. There is
enough grease in the included tube is for two applications.
enough grease in the included tube is for two applications.
warning