Trek Bicycle Corporation C97371576 Manuel D’Utilisation
TransmiTr
Quick Start Manual
This manual gives basic instructions on
the installation and use of the Bontrager
TransmitR lighting system, which is
ANT+ compatible. For the complete
manual, check our web site
trekbikes.com
The full manual includes this
additional information:
• Pairing
• Manual operation
• Listing of all modes, run times
• Troubleshooting
• Battery types (and installation
the installation and use of the Bontrager
TransmitR lighting system, which is
ANT+ compatible. For the complete
manual, check our web site
trekbikes.com
The full manual includes this
additional information:
• Pairing
• Manual operation
• Listing of all modes, run times
• Troubleshooting
• Battery types (and installation
in Remote)
• Turn signal and high beam headlight
function
• Recycling and disposal
• Compliance info
• Warranty
• Compliance info
• Warranty
imPOrTanT: Check your local lighting
laws. Flashing lights and full brightness
may not be allowed in all locations. Ion
800 RT and Flare RT do not conform to
the German road traffic regulation StVZO.
laws. Flashing lights and full brightness
may not be allowed in all locations. Ion
800 RT and Flare RT do not conform to
the German road traffic regulation StVZO.
“To see” light
The Ion 800 RT is a “To See” light, a
headlight for primary vision when riding in
low light. It can also function as a “To Be
Seen” light when in flash mode, although
the amber side lenses do not direct a
substantial amount of light. Note that for
best results, a rider should employ BOTH
a To See light and a To Be Seen light.
The Ion 800 RT is a “To See” light, a
headlight for primary vision when riding in
low light. It can also function as a “To Be
Seen” light when in flash mode, although
the amber side lenses do not direct a
substantial amount of light. Note that for
best results, a rider should employ BOTH
a To See light and a To Be Seen light.
sETUP
Pairing the TransmitR Remote to
TransmitR Lights
TransmitR Lights
Corner Buttons
-Control individual lights
-Shows light mode when
pressed
-Shows light mode when
pressed
Center Button
-System On/Off (all lights)
-Shows battery status of
light when paired button
is pressed
High beam (headlights
only)
-Shows battery status of
light when paired button
is pressed
High beam (headlights
only)
1. For each light to be paired, quick-
press the power button on the light,
then press and hold the power button
to turn off.
nOTE: If you purchased the TransmitR
Wireless Light Set, [Part Number
503063] with the Ion 800RT, Flare RT
and TransmitR Remote in one package,
skip ahead to section ‘Using the
TransmitR Remote’
2. Place all TransmitR lights to be paired
within 15cm/6 inches of the remote.
press the power button on the light,
then press and hold the power button
to turn off.
nOTE: If you purchased the TransmitR
Wireless Light Set, [Part Number
503063] with the Ion 800RT, Flare RT
and TransmitR Remote in one package,
skip ahead to section ‘Using the
TransmitR Remote’
2. Place all TransmitR lights to be paired
within 15cm/6 inches of the remote.
3. Press and hold the center button on
the remote for 8 seconds until the corner
buttons begin flashing.
The remote will find a TransmitR light and
the light will begin flashing. At the same
time, the center button on the remote
will turn from red to green, signifying a
connection.
4. Press the corner button on the remote
that you would like to have paired to the
light. The light will stop flashing when
it has been paired to the remote. The
center button will change back to red
and search for additional lights to pair.
5. If the remote locates another light,
repeat step 4.
6. When all TransmitR lights (up to seven)
have been paired, press the center
button of the remote to exit pairing. It will
turn from red to OFF.
Your TransmitR system is now paired and
ready for use.
the remote for 8 seconds until the corner
buttons begin flashing.
The remote will find a TransmitR light and
the light will begin flashing. At the same
time, the center button on the remote
will turn from red to green, signifying a
connection.
4. Press the corner button on the remote
that you would like to have paired to the
light. The light will stop flashing when
it has been paired to the remote. The
center button will change back to red
and search for additional lights to pair.
5. If the remote locates another light,
repeat step 4.
6. When all TransmitR lights (up to seven)
have been paired, press the center
button of the remote to exit pairing. It will
turn from red to OFF.
Your TransmitR system is now paired and
ready for use.
UsinG THE
TransmiTr rEmOTE
TransmiTr rEmOTE
Controlling Lights with the
TransmitR Remote
TransmitR Remote
To turn on all lights
ON: Quick-press the center button.
OFF: Press and hold the center button.
To turn on an individual light
ON: Quick-press the corner button that
controls the light.
OFF: Press and hold the same button.
To change modes of an
individual light
Each quick-press of a button that
controls a light will cycle through
the modes.
Trail Configuration enables the Ion
800 RT to toggle between 800 and 450
lumen steady modes. To enable and
disable press and hold the power button
for 8 seconds with the light off. The
main LED will flash once indicating trail
configuration has been enabled/disabled.
seeing Battery Power status of the
light on the remote
When a corner button is pressed, the
center button will show the battery status
of the light
ON: Quick-press the center button.
OFF: Press and hold the center button.
To turn on an individual light
ON: Quick-press the corner button that
controls the light.
OFF: Press and hold the same button.
To change modes of an
individual light
Each quick-press of a button that
controls a light will cycle through
the modes.
Trail Configuration enables the Ion
800 RT to toggle between 800 and 450
lumen steady modes. To enable and
disable press and hold the power button
for 8 seconds with the light off. The
main LED will flash once indicating trail
configuration has been enabled/disabled.
seeing Battery Power status of the
light on the remote
When a corner button is pressed, the
center button will show the battery status
of the light
The light may be hot to touch.
CaUTiOn
Button light color
Power remaining
Green
More than 25%
red
Between 5% and 25%
Blinking red
Less than 5%
Welcome.
About this Manual
This is the quick start manual for your
TransmitR lighting system. Check for
updates at bontrager.com.
BT16_ION800RT_FLARERT_QSG_V1
BT16_MANUAL_TransmitR_QuickStartv8.indd 1
6/13/16 1:14 PM