Shenzhen Jerehong Electronic Co. Ltd 8057274 Manuel D’Utilisation
d
l
o
F
d
l
o
F
d
l
o
F
CHARGING THE HEADPHONES
1. For first time use, charge the
headphones for 12 hours.
2. To charge the headphones, ensure
the headphones are OFF by sliding
the Power Switch to OFF on
headphones until the Power LED is
OFF. Place the headphones on the
top of transmitter ensuring the
charging contacts are aligned. The
transmitter’s CHARGE LED will blink
BLUE to show the headphones are
charging. When the headphones
are fully charged, the CHARGE LED
is solid BLUE.
headphones for 12 hours.
2. To charge the headphones, ensure
the headphones are OFF by sliding
the Power Switch to OFF on
headphones until the Power LED is
OFF. Place the headphones on the
top of transmitter ensuring the
charging contacts are aligned. The
transmitter’s CHARGE LED will blink
BLUE to show the headphones are
charging. When the headphones
are fully charged, the CHARGE LED
is solid BLUE.
TROUBLE SHOOTING
NO SOUND
NO SOUND
• Ensure the AC/DC adapter is
securely plugged into the transmitter.
• Ensure the headphones are
powered on.
• Ensure the headphones and the
transmitter are synced.
• The headphones may need to be
charged.
• The headphones may need to move
closer to the transmitter.
• Ensure the audio device is switched
ON.
• The volume of the audio device may
need to be increased.
• If there is interference or poor signal
reception, audio from the headphones
will mute and the Power/RF LED is
solid RED. Press the SCAN Buttons
on transmitter and on headphones
at same time for 10 seconds until the
headphones’ LED turn SOLID BLUE
again.
securely plugged into the transmitter.
• Ensure the headphones are
powered on.
• Ensure the headphones and the
transmitter are synced.
• The headphones may need to be
charged.
• The headphones may need to move
closer to the transmitter.
• Ensure the audio device is switched
ON.
• The volume of the audio device may
need to be increased.
• If there is interference or poor signal
reception, audio from the headphones
will mute and the Power/RF LED is
solid RED. Press the SCAN Buttons
on transmitter and on headphones
at same time for 10 seconds until the
headphones’ LED turn SOLID BLUE
again.
USING THE HEADPHONES
WITH WIRED CONNECTION
WITH WIRED CONNECTION
1. Connect the headphones directly
to an audio source by plugging one
end of a 3.5mm-to -3.5mm cable (
included) into the AUX-IN Port at the
bottom of the headphones and other
end into the audio source.
2. Use the volume controls on the audio
source to change the volume.
to an audio source by plugging one
end of a 3.5mm-to -3.5mm cable (
included) into the AUX-IN Port at the
bottom of the headphones and other
end into the audio source.
2. Use the volume controls on the audio
source to change the volume.
TRANSMITTER SET UP
1. Plug the AC/DC power adapter into
the DC Port located on the rear of
the transmitter. Plug the other end
of the AC/DC power adapter into
an electrical wall outlet.
2. Slide the Power Switch to ON . The
transmitter’s Power LED is solid
RED.
3. Connect the transmitter to an audio
source using the included RCA and
audio cables.
the DC Port located on the rear of
the transmitter. Plug the other end
of the AC/DC power adapter into
an electrical wall outlet.
2. Slide the Power Switch to ON . The
transmitter’s Power LED is solid
RED.
3. Connect the transmitter to an audio
source using the included RCA and
audio cables.
Note:
If CHARGE LED disappears, please
check if the charging contacts of both
the headphones and transmitter are
well aligned.
check if the charging contacts of both
the headphones and transmitter are
well aligned.
CARE AND STORAGE
1. Dust the headphones and transmitter
with a soft, dry cloth.
2. Store the headphones and transmitter
in a cool, dry place.
with a soft, dry cloth.
2. Store the headphones and transmitter
in a cool, dry place.
SPECIFICATIONS
Power Supply (Transmitter):
DC 5V, 300mA
Power Supply (Headphones):
3.7V 900mAh
Frequency: 2.4-2.48 GHz Digital
Transmission mode: GFSK
Range: Up to 100ft (approx. 30m)
S/N Radio: 75dB
Frequency Response: 30Hz~20KHz
Charging Time: Approx. 4 hours
(subsequent uses after first initial
charge of 12 hours)
Battery Life: Approx. 12 hours
DC 5V, 300mA
Power Supply (Headphones):
3.7V 900mAh
Frequency: 2.4-2.48 GHz Digital
Transmission mode: GFSK
Range: Up to 100ft (approx. 30m)
S/N Radio: 75dB
Frequency Response: 30Hz~20KHz
Charging Time: Approx. 4 hours
(subsequent uses after first initial
charge of 12 hours)
Battery Life: Approx. 12 hours
USING THE HEADPHONES
WITH TRANSMITTER
WITH TRANSMITTER
1. To turn the headphones on, slide the
Power Switch to ON. The Power/RF
LED is in solid RED.
2. The headphones will automatically
sync to the transmitter. When the
headphones are attempting to set up
a connection with the transmitter, the
Power/RF LED will blink RED.
When the headphones and
transmitter are synced, the
headphones’ LED is solid BLUE.
3. Use the Volume buttons on the
headphones and the audio source
to change the volume.
4. Slide the BASS/NORMAL Switch to
BASS for bass boost function under
RF wireless mode.
Note: It has no bass boost function
under wired connection.
5. After 5 minutes of no audio signal
detected, the Power/RF LED turns
solid RED.
6. To turn the headphones off, slide
the Power Switch to OFF. The
Power/RF LED will light off.
Power Switch to ON. The Power/RF
LED is in solid RED.
2. The headphones will automatically
sync to the transmitter. When the
headphones are attempting to set up
a connection with the transmitter, the
Power/RF LED will blink RED.
When the headphones and
transmitter are synced, the
headphones’ LED is solid BLUE.
3. Use the Volume buttons on the
headphones and the audio source
to change the volume.
4. Slide the BASS/NORMAL Switch to
BASS for bass boost function under
RF wireless mode.
Note: It has no bass boost function
under wired connection.
5. After 5 minutes of no audio signal
detected, the Power/RF LED turns
solid RED.
6. To turn the headphones off, slide
the Power Switch to OFF. The
Power/RF LED will light off.