Toshiba RD-XV48DTKF Manuel D’Utilisation

Page de 103
14
EN
27 VARIABLE SKIP button (HDD/DVD)
• Skips by the amount of time set in advance.
28 DISC MENU button (HDD/DVD)
• Press to display the Disc menu during playback.
• Press to change the Original and Playlist on the 
TV screen.
29 ENTER button
• Press to acknowledge or approve a menu 
selection.
• While watching a DVB channel, press to display 
the “Quick select” menu.
30 RETURN button
• Press to return to the previously displayed menu 
screen.
31 FWD D button
• When playback is paused, press to forward slowly.
(HDD/DVD)
• During playback, press to fast forward.
(VHS)
• Press to advance the videotape rapidly.
• Press to view the picture rapidly in forward 
during playback.
32 STOP C button
• Press to stop playing back or recording.
33 SKIP G button (HDD/DVD)
• During playback, press to skip to the next 
chapter or track.
• When playback is paused, press to advance 
step by step.
34 HDD button 
• Press to select the HDD output mode.
35 DVD button
• Press to select the DVD output mode.
36 REC I button
• Press once to start a recording.
• Press repeatedly to start a One-touch Timer 
Recording.
37 REC MODE button
• Press to switch the recording mode.
38 SAT.LINK button (HDD) 
• Press to activate the Satellite Link Timer 
Recording.
39 AUDIO
D button
• For analogue channels when receiving a 
bilingual broadcast, press to change the audio 
out setting to “Main”, “Sub” or “Main/Sub”.
• Press to change the bilingual audio source of an 
external equipment to “Main”, “Sub” or “Main/Sub”. 
(Available only when the “External Input Audio” in 
“Setup” menu is set to “Bilingual” in advance.)
• Press to select the sound mode for DVB channels.
(HDD/DVD)
• Press to display the audio menu during playback.
(VHS)
• During playback of Hi-Fi videotape, press to 
change the audio out setting to “STEREO”, 
“LEFT”, “RIGHT” and “MONO”.
Note
• If you turn off this unit, [OPEN
\CLOSE A] on the remote 
control is not available. Be sure to use [OPEN
\CLOSE] 
or [EJECT/STOP] on the unit.
Installing Batteries in the 
Remote Control
Install two R6 (AA) batteries (supplied) into the 
remote control, carefully match with the polarity 
indicated inside the battery compartment.
Caution
• Incorrect use of batteries can result in hazards such 
as leakage and bursting. 
• Do not mix new and old batteries together.
• Do not use different kinds of batteries together.
• Make sure that the plus (+) and minus (–) ends of 
each battery match the indications inside the battery 
compartment.
• Remove batteries if the equipment will not be used 
for a month or more.
• When disposing used batteries, please comply with 
governmental regulations or the public instructions 
for environmental protection that apply in your 
country or area.
• Do not recharge, short-circuit, heat, burn or 
disassemble batteries.
About the Remote Control
• Make sure there is no obstacle between the remote 
control and the remote control sensor on the unit.
• Use within the operating range and angle as shown.
• The maximum operable range as follows:
• Remote control operation may become unreliable if 
the remote control sensor of the unit is being 
exposed by the strong sunlight or fluorescent light.
• Remote controls for different devices can interfere 
with each other. Be careful when using remote 
controls for other equipment located close to the 
unit.
• Replace the batteries when the operating range of 
the remote control reduces.
Button names described in the Owner’s Manual
The instructions in this manual are described mainly 
with the operations using the remote control. Some 
operations can be carried out using the buttons on 
the front panel.
Line of sight:
approximately 7 m
Either side of centre: approximately 7 m within 
30 degrees
2
1
3
VCR
REC
PROGRAM
DUBBING
VCR
HDD
DVD
SELECT
REC
HDD/DVD
SELECT
SELECT
DVD
VCR
DVD
HDD
DVD
HDD
Within 
about 7 m
Remote control
7 m (30°)
7 m
7 m (30°)
E3NG0FD_EN.book  Page 14  Wednesday, January 30, 2008  10:37 AM