GE PSB1200NBB/WW Manuel D’Utilisation

240445

Listed by 

Underwriters 

Laboratories

PSB1200NBB/WW 

GE Profile Advantium

® 

120 Volt - 30" Wall Oven

 

For answers to your Monogram,

® 

GE Profile

™

 or  

GE

®

 appliance questions, visit our website at 

ge.com or call GE Answer Center

®

 service,  

800.626.2000.

cooking_tower_solid_floor.eps

CL

(Must support 130 lbs.)

2 x 4’s or

equivalent

solid floor

Suitable

bracing

to support

runners

21-5/8"

over centerline

of cabinet

PSB1200/1 without 
accessory drawer

30

29-25/32

19-1/8

21-3/4

25-1/8

17-1/2

23-1/2

PSB1200/1 with  
accessory drawer

30

29-25/32

22-1/4

21-3/4

25-1/8 to 

28-1/2*

21

23-1/2

*For existing cutouts a maximum width of 28-1/2" is acceptable

Note: 2" minimum  
between cutouts when  
installed above warming  
drawer or single wall oven. 
Installation Information:  
Before installing, consult  
installation instructions  
packed with product for   
current dimensional data.
Note: PSB1200/1 series  
Advantium can be  
installed below GE/GE  
Profile non-downdraft  
gas and electric cooktops.  
It CANNOT be installed  
below induction or Monogram 
(2GU3841385) gas cooktops.
Note: PSB1200/1 series Advantium 
oven comes with two lower trim pieces. 
One is for use above 36-inch height 
installations and one is for use below 36-
inch installations. Use of the accessory 
drawer will replace the bottom trim piece 
for applicable installations. Please see 
installation instructions for full details.

adv_240_120_cooktower_dia.eps

1" Min. above toekick or adjust 
to oven installation height

2" MIN between cutouts

2-1/2" MIN between cutouts 
recommended—2" MIN required

9-1/4" cutout height
28-1/2" cutout width

Junction box location

A

B

A

B

Construct Solid Bottom 
MIN 3/8" Plywood Supported by
2 x 4 or 1 x 2 Runners, all Four Sides.
(Must Support 150 lbs. for Advantium)
(Must Support 200 lbs. for Wall Oven)

4-3/16

D

Excluding

Handle

H

W

Conduit

(46" long)

Cabinet width

(240-volt models only)

4-3/16"

23-1/2"

Cutout depth

Junction 

box location

17-1/2"

Cutout height

29-25/32"

19-1/32"

21-1/2"

Excluding

Handle

Conduit

(48-1/2" 

long)

B

30"

5" min.from

floor 1" min.

above toekick

A= Allow 1" overlap of oven over bottom edge of cutout, and allow

    1-1/4" overlap at top edge of cutout.

B= Allow 11/16"-3/4" for overlap of oven over side edges of cutout.

Construct Solid

Bottom Min. 

3/8" Plywood

Supported by

2 x 4 or 1 x 2

Runners, all 

Four Sides.

(Must Support

150 lbs.)

A

Note: Cabinets installed adjacent 
to wall ovens must have an adhesion 
spec of at least 194° F temperature rating.

4-3/16"

23-1/2"

Cutout depth

Junction 

box location

17-1/2"

Cutout height

29-25/32"

19-1/32"

21-1/2"

Excluding

Handle

Conduit

(48-1/2" 

long)

B

30"

5" min.from

floor 1" min.

above toekick

A= Allow 1" overlap of oven over bottom edge of cutout, and allow

    1-1/4" overlap at top edge of cutout.

B= Allow 11/16"-3/4" for overlap of oven over side edges of cutout.

Construct Solid

Bottom Min. 

3/8" Plywood

Supported by

2 x 4 or 1 x 2

Runners, all 

Four Sides.

(Must Support

150 lbs.)

A

Note: Cabinets installed adjacent 
to wall ovens must have an adhesion 
spec of at least 194° F temperature rating.