Entes MPR-63 Mains-analysis device, Mains analyser MPR-63 Manuel D’Utilisation
Codes de produits
MPR-63
Important note for system connection
indicators indicate the existence of the three phases.
If indicator (Phase sequence is not correct) is seen, you have to change any of the 2 phases before proceeding.
(L1 - L2, L2 - L3 or L1 - L3)
(L1 - L2, L2 - L3 or L1 - L3)
ATTENTION : Consult the operating instructions before using the equipment.
If these precautions are not properly observed and carried out, it can cause physical accident
or damage to the equipment or the installation.
The manufacturer or the authorized seller is not responsible for the consequences
If these precautions are not properly observed and carried out, it can cause physical accident
or damage to the equipment or the installation.
The manufacturer or the authorized seller is not responsible for the consequences
resulting from failure to comply with these precautions.
SAFETY PRECAUTIONS
This equipment has been manufactured and tested and it has left the factory in perfectly safe condition.
To preserve this and ensure safe operation of the equipment the user should comply with the instructions
which are mentioned in this manual.
Before installing, check that the operating and network voltages are the same!
Before carrying out any work on the equipment, check that it is disconnected from the electrical supply.
If the equipment is no longer completely safe to use, it should be taken out of service and
protected against any accidental use.
To preserve this and ensure safe operation of the equipment the user should comply with the instructions
which are mentioned in this manual.
Before installing, check that the operating and network voltages are the same!
Before carrying out any work on the equipment, check that it is disconnected from the electrical supply.
If the equipment is no longer completely safe to use, it should be taken out of service and
protected against any accidental use.
Operator Safety
Read the following recommendations carefully before installing and operating the equipment.
The equipment described in this manual is designed only to be used by trained personnel.
Maintenance work must be carried out only by qualified, authorised personnel.
Personnel must observe the usual safety procedures for safe operation and during any maintenance work.
Maintenance work must be carried out only by qualified, authorised personnel.
Personnel must observe the usual safety procedures for safe operation and during any maintenance work.
Breakdown Precautions
If you suspect that the equipment may no longer be safe (e.g. because of transport or operational damage),
it must be taken out of service and protected against any accidental use.
The equipment should be handed over to authorised technicians for checking.
it must be taken out of service and protected against any accidental use.
The equipment should be handed over to authorised technicians for checking.
Cleaning Instructions
Disconnect the equipment from the electrical supply and only use a damp cloth to clean the external surfaces.
Do not use any abrasive materials or solvents. Do not allow any moisture to reach the connection terminals.
Do not use any abrasive materials or solvents. Do not allow any moisture to reach the connection terminals.
Figure 1: The existence of three phases on LCD.
1
MPR63-
22/23/42/43
NETWORK ANALYSER
ver.1.74
A4194b
Standards which are applied to the device:
EN 61000-6-2, EN 61000-6-4, EN 55016-2-1, EN 55016-2-3, EN 55011, EN 61000-3-2, EN 61000-3-3, EN 61010-1
EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-5, EN 61000-4-6, EN 61000-4-8, EN 61000-4-11
EN 61000-6-2, EN 61000-6-4, EN 55016-2-1, EN 55016-2-3, EN 55011, EN 61000-3-2, EN 61000-3-3, EN 61010-1
EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-5, EN 61000-4-6, EN 61000-4-8, EN 61000-4-11