Panasonic HE2AN24 PCB Mount Relay 24V 2 NO, DPST-NO HE2AN24 Fiche De Données
Codes de produits
HE2AN24
HE
5
ds_61120_0000_en_he: 061006J
1 Form A Type
MOUNTING METHOD
NOTES
For Cautions for Use, see
1. Maximum switching power
2. Life curve
3. Contact temperature rise (DC type)
Measured portion: Inside the coil
Contact current: 30 A
Contact current: 30 A
100
50
30
20
30
20
10
5
1
0.5
30
100
500 1,000
Contact voltage, V
Contact current, A
AC resistive
DC resistive
10
5
100
50
1,000
500
30
35
20
25
10
15
5
0
Contact current, A
No. of operations,
×
10
4
250 V AC resistive
30 V DC resistive
30 V DC resistive
70
60
50
40
30
20
10
0
100
110
120
20°C
60°C
40°C
Coil applied voltage, %V
Temperature rise, °C
4. Ambient temperature characteristics
Sample: HE2aN-AC120V, 6 pcs.
40
60
80
20
-10
0
-20
-50
-20
-30
x-
x-
Ambient
temperature, °C
temperature, °C
Pick-up
voltage
voltage
Drop-out
voltage
voltage
Rate of
change, %
20
10
1. Plug-in terminal type
2. Screw terminal type
3. Allowable installation wiring size for
screw terminal types and terminal blocks
screw terminal types and terminal blocks
Due to the UP terminals, it is possible to
either directly connect the wires or use
crimped terminal
either directly connect the wires or use
crimped terminal
M4 screw
Faston No.250
Washer
M4 screw
Washer
1a type
2.6 mm or 5.5 mm
2
2a type
2.0 mm or 3.5 mm
2
1. The dust cover should not be removed
since doing so may alter the
characteristics.
2. Avoid use under severe environmental
conditions, such as high humidity,
organic gas or in dust, oily locations and
locations subjected to extremely frequent
shock or vibrations.
3. When mounting, use spring washers.
Optimum fastening torque ranges from 5
kg to 7 kg·cm
since doing so may alter the
characteristics.
2. Avoid use under severe environmental
conditions, such as high humidity,
organic gas or in dust, oily locations and
locations subjected to extremely frequent
shock or vibrations.
3. When mounting, use spring washers.
Optimum fastening torque ranges from 5
kg to 7 kg·cm
4.5 to 6 pounds·inch
.
4. Firmly insert the receptacles so that
there is no slack or looseness. To remove
a receptacle, 2 to 4 kg of pulling strength
there is no slack or looseness. To remove
a receptacle, 2 to 4 kg of pulling strength
is required. Do not remove more than
one receptacle at one time.Always
remove one receptacle at a time and pull
it straight outwards.
5. Install the relay so that it lies in
direction A (up-down direction). (Pick-up
voltage and drop-out voltage values are
those when installed in direction A.)
6. When using the AC type, the operate
time due to the in-rush phase is 20 ms or
more. Therefore, it is necessary for you
to verify the characteristics for your actual
circuit. Moreover, the release time for the
NC side of the 2a1b type requires the
one receptacle at one time.Always
remove one receptacle at a time and pull
it straight outwards.
5. Install the relay so that it lies in
direction A (up-down direction). (Pick-up
voltage and drop-out voltage values are
those when installed in direction A.)
6. When using the AC type, the operate
time due to the in-rush phase is 20 ms or
more. Therefore, it is necessary for you
to verify the characteristics for your actual
circuit. Moreover, the release time for the
NC side of the 2a1b type requires the
same verification.
7. When using the push-on blocks for the
screw terminal type, use crimped
terminals and tighten the screw-down
terminals to the torque’s listed below.
7. When using the push-on blocks for the
screw terminal type, use crimped
terminals and tighten the screw-down
terminals to the torque’s listed below.
8. All AC240V types are rated for double
coil voltage, both AC 220V AC 240V.
coil voltage, both AC 220V AC 240V.
M4.5 screw
147 N-cm to 166.6 N-cm
(15 to 17 kg·cm)
(15 to 17 kg·cm)
M4 screw
117.6 N-cm to 137 N-cm
(12 to 14 kg·cm)
(12 to 14 kg·cm)
M3.5 screw
78.4 N-m to 98 N-cm
(8 to 10 kg·cm)
(8 to 10 kg·cm)