Panasonic ST124F PCB Mount Relay 24V 1 NO / 1 NC ST124F Fiche De Données
Codes de produits
ST124F
ST
5
ds_61A09_en_st: 070313D
PRECAUTIONS FOR USE (SOCKET)
ACCESSORIES
ST RELAYS
SOCKET
VDE
ST relay socket
ST-PS
PC board terminal socket
PC board terminal socket
ST-SS
Solder terminal socket
Solder terminal socket
FEATURES
1. Possible to fit or remove the
chassis with one touch (t = 0.6 mm
to 2.2 mm
to 2.2 mm
.024 inch to .087 inch
)
2. Easy design of PC board pattern
(2.54 mm x 4 pitch DIL terminal array)
3. Complies with Japan Electrical
Appliance and Material Safety Law.
(UL and VDE certification)
(UL and VDE certification)
4. High breakdown voltage.
SPECIFICATIONS
Item
Specifications
Breakdown voltage (Initial)
Between contact and coil: 4,000 Vrms for 1 min. (Detection current: 10 mA)
Between contact and terminal: 2,000 Vrms for 1 min.
Between contact and terminal: 2,000 Vrms for 1 min.
Insulation resistance (Initial)
Min. 1,000 M
between terminals (500V DC)
Heat resistance
150
C
302
F
for 1 hr
Max. continuous current
10 A
Relay insertion life
15 times
31.6
35.4
16.6
8
1
7
2
6
3
5
4
14.6
16.4
10.16
1.05
0.3
5.5
4
4.3
0.27
10.16
7.62
7.62
1.244
1.394
.654
.575
.646
.400
.041
.012
.217
.158
.169
.011
.400
.300
.300
31.6
35.4
16.6
8
1
7
2
6
3
5
4
14.6
16.4
10.16
2.3
0.3
5.5
4
5.3
0.27
10.16
7.62
7.62
1.244
1.394
.654
.575
.646
.400
.012
.217
.158
.209
.011
.400
.300
.300
.090
DIMENSIONS
(Unit: mm
inch
)
ST-PS
ST-SS
1. PC board mounting method
PC board pattern
PC board pattern
The terminal configuration is symmetrical
on the left and right, so an arrow mark
on the left and right, so an arrow mark
is stamped on the socket to prevent mis-
insertion. We recommend printing the
same arrow mark
insertion. We recommend printing the
same arrow mark
on the component
mounting side (side opposite from
pattern) of the PC board. In this case, the
terminal configuration becomes the
terminal nos. noted near the drilling
holes.
pattern) of the PC board. In this case, the
terminal configuration becomes the
terminal nos. noted near the drilling
holes.
2. Chassis cutout
Chassis cutting dimensions
Chassis cutting dimensions
If the chassis hole is punched with a
press, set so the release R on the front
side (A side).
The range for chassis thickness is 0.6 to
2.2 mm
press, set so the release R on the front
side (A side).
The range for chassis thickness is 0.6 to
2.2 mm
.024 to .087 inch
.
3. Relay mounting and removal
(1) Align the directions of the relay and
socket.
(1) Align the directions of the relay and
socket.
(2) Insert the relay all the way in, so it is
securely in place.
securely in place.
(3) Press the part indicated by A in the B
direction, and fasten by placing the hook
on the relay.
direction, and fasten by placing the hook
on the relay.
(4) When removing the relay, completely
release the hooks on both sides and pull
the relay out.
release the hooks on both sides and pull
the relay out.
2.54
8-1.5 dia.
8
7
6
5
1
2
3
4
2.54
Contact
terminal
interval
terminal
interval
Coil
terminal
interval
terminal
interval
.100
8-.060 dia.
.100
15.0
±0.2
32.5
±0.1
.591
±.008
1.280
±.004
Claw for chassis
fastening
fastening
Chassis t = 0.6 to 2.2
Press
A side
.024 to .087
Relay
Hinge
mechanism
mechanism
Relay case
cross-section
B
(Fastening complete)
(Before fastening)
A