MEAN WELL LED driverLED-switching power supply PLC-30-12 PLC-30-12 Fiche De Données

9V

15V

10.5 ~ 15V

12V

8.4 ~ 12V

20V

14 ~ 20V

24V

16.8 ~ 24V

27V

18.9 ~ 27V

36V

25.2 ~ 36V

48V

33.6 ~ 48V

3.3A

2A

2.5A

1.5A

1.25A

1.12A

0.84A

0.63A

0 ~ 3.3A

0 ~ 2A

0 ~ 2.5A

0 ~ 1.5A

0 ~ 1.25A

0 ~ 1.12A

0 ~ 0.84A

0 ~ 0.63A

29.7W

30W

30W

30W

30W

30.24W

30.24W

30.24W

2.6Vp-p

2.6Vp-p

2Vp-p

2.6Vp-p

2.4Vp-p

2.3Vp-p

3.6Vp-p

3.7Vp-p

±3.0%

±10%

±5.0%

2000ms / 230VAC    3000ms / 115VAC at full load

90 ~ 264VAC          127 ~ 370VDC

47 ~ 63Hz

PF>0.95/115VAC, PF>0.9/230VAC at full load (Please refer to "Power Factor Characteristic" curve)

80%

83.5%

82.5%

84%

84%

84.5%

85%

85.5%

10 ~ 14V

17 ~ 22V

14 ~ 16V

23 ~ 26V

27 ~ 34V

31 ~ 35V

40 ~ 50V

53 ~ 63V

0.4A/115VAC     0.2A/230VAC

<0.5mA / 240VAC

100 ~ 110% 

Protection type : Constant current limiting, recovers automatically after fault condition is removed

Hiccup mode, recovers automatically after fault condition is removed.

I/P-O/P:3.75KVAC

I/P-O/P:100M Ohms / 500VDC / 25

/ 70% RH

℃

-30 ~ +50

 (Refer to "Derating Curve")

℃

20 ~ 95% RH non-condensing

-40 ~ +80

, 10 ~ 95% RH

℃

±

℃

℃

0.06%/

 (0 ~ 50

)

10 ~ 500Hz, 2G 12min./1cycle, period for  72min. each along X, Y, Z axes

625.5K hrs min.      MIL-HDBK-217F (25

)

℃

160*46*30mm (L*W*H)

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25  of ambient temperature.

℃

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.    
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. Derating may be needed under low input voltage. Please check the static characteristics for more details.
5. Output voltage can be adjusted through the SVR1 on the PCB; limit of output constant current level can be adjusted through the SVR2 on the PCB.
6.  lease refer to "DRIVING METHODS OF LED MODULE".

P

7. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the 
    complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
8. Direct connecting to LEDs is suggested, but is not suitable for using additional drivers.

0.2Kg; 70pcs/15Kg/0.96CUFT

Protection type : Shut down o/p voltage, re-power on to recover

30W Single Output LED Power Supply

‧

Universal AC input / Full range

‧

Adjustable output voltage and current level

‧

Protections: Short circuit / Over current / Over voltage / Over temperature 

‧

Cooling by free air convection

‧

Built-in constant current limiting circuit

‧

Fully isolated plastic case with terminal block style of I/O

‧

Built-in active PFC function, comply with EN61000-3-2 class C

     (

)

Pin 25W

≧

‧

Ⅱ

Class   power unit, no FG

‧

Class 2 power unit

‧

100% full load burn-in test

‧

High reliability

‧

Suitable for LED lighting and moving sign applications 

(Note.2)

‧

Compliance to worldwide safety regulations for lighting 

‧

2 years warranty

■

 Features :

Shut down o/p voltage, re-power on to recover

UL1310, TUV EN61347-1, EN61347-2-13, CAN/CSA C22.2 No. 223-M91(except for 48V), J61347-1, J61347-2-13 approved

6.3 ~ 9V

Compliance to EN55015, EN61000-3-2 Class C (Pin

25W), Class D (>70% load) ; EN61000-3-3

≧

Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61547, light industry level,  criteria B

11.4 ~ 13.2V

8.55 ~ 9.9V

1.875 ~ 2.575A

2.475 ~ 3.399A

14.5 ~ 16.5V

1.5 ~ 2.06A

19 ~ 22V

22.8 ~ 26.4V

0.938 ~ 1.288A

25.65 ~ 29.7V

0.84 ~ 1.1536A

34.2 ~ 39.6V

0.63 ~ 0.865A

45.6 ~ 52.8V

0.473 ~ 0.649A

1.125 ~ 1.545A

( for 48V only)

( except for 48V )

COLD START 35A(t

=25  s measured at 50% I

) at 230VAC 

width

peak

μ