Shurflo Low voltage submersible pump 355-100-00 3780 l/h 2.5 m 355-100-00 Fiche De Données
Codes de produits
355-100-00
TROUBLESHOOTING
Symptoms
Check For
No water pumped
Pump not running
Pump not running
Reset pump switch. Blown fuse. Reversed polarity damaged switch board.
Wire connections. Impeller or float switch plugged with debris.
Wire connections. Impeller or float switch plugged with debris.
Reduced water flow
Impeller/screen plugged with debris. Pinched/clogged discharge tubing. Discharge tubing sagging below
pump causing air lock (Tubing MUST go "UP" from pump to through hull fitting). Low voltage to pump;
check. Battery/wire connections.
Low flow
Polarity reversed (on pump only); check wiring. Use smooth bore (I.D.) discharge tubing only.
Is through hull fitting I.D. smaller than pump discharge port?
Is through hull fitting I.D. smaller than pump discharge port?
Runs continuously
Check boat for leaks; Clean accumulated debris from float mechanism.
LIMITED WARRANTY
SHURflo warrants its SHURflo™ series bilge pumps to be free of defects in material and workmanship under normal use for a
period of three (3) years from the date of manufacture, as indicated on the pump label. Returns are to be shipped prepaid to
SHURflo. This warranty is only a representation of the complete marine products limited warranty, outlined by Service Bulletin
#1050. Call or write for a copy.
period of three (3) years from the date of manufacture, as indicated on the pump label. Returns are to be shipped prepaid to
SHURflo. This warranty is only a representation of the complete marine products limited warranty, outlined by Service Bulletin
#1050. Call or write for a copy.
CLEANING:
Impeller: Snap pump out of base plate by pressing in the tabs. Clean debris and snap back in
place. Test unit.
Switch: Remove debris or build-up. Reinstall switch and test unit.
Switch test: Turn power on to pump switch.
WIRING:
Check all wire connections regularly. Repair sign of corrosion.
Impeller: Snap pump out of base plate by pressing in the tabs. Clean debris and snap back in
place. Test unit.
Switch: Remove debris or build-up. Reinstall switch and test unit.
Switch test: Turn power on to pump switch.
WIRING:
Check all wire connections regularly. Repair sign of corrosion.
Specifications given at design voltage 13.6 VDC per ABYC recommendations.
Pump Power leads: 3 ft. [0.9 M] #16 tinned stranded copper wire to minimize corrosion. Positive (+) brown; Ground (–) black
Switch Leads (If equipped with SHURflo Piranha Switch): Automatic (+) brown; Manual (+) brown & white; Ground (--) black
Temperature limits: 33ºF—140ºF [0ºC—60ºC]. All models rated for continuous duty.
Approvals: Ignition Protected, ISO 8846, ABYC, NMMA Type Accepted, CE
Pump Power leads: 3 ft. [0.9 M] #16 tinned stranded copper wire to minimize corrosion. Positive (+) brown; Ground (–) black
Switch Leads (If equipped with SHURflo Piranha Switch): Automatic (+) brown; Manual (+) brown & white; Ground (--) black
Temperature limits: 33ºF—140ºF [0ºC—60ºC]. All models rated for continuous duty.
Approvals: Ignition Protected, ISO 8846, ABYC, NMMA Type Accepted, CE
Model #:
0 ft [0 M]
3 ft [1 M]
6 ft [2 M]
Max Head Ft [M]
Max Amps
Fuse
Outlet Port
Dimensions
355-020-10
380 [1438]
340 [1157]
240 [817]
7.5 [2.2]
1.7
2.5
3/4"
4-1/2" X 3"
355-010-10
500 [1892]
430 [1464]
270 [918]
7.5 [2.2]
1.8
2.5
3/4"
4-1/2" X 3"
355-110-10
700 [2649]
600 [2043]
500 [1702]
10 [3]
3.2
5
3/4"
4-1/2" X 3"
355-100-10
1000 [2649]
840 [2861]
650 [2214]
11 [3.3]
3.4
6
1-1/8"
4-1/2" X 3"
FLOW GPM [LPM]
TECHNICAL DATA
Repair Kit for all
models: 94-750-00
Do not pump oil, diesel fuel, gasoline or other flammable liquids with this pump.
This pump does not prevent the discharge of oil or other chemicals into the water. Please take appropriate
measures to prevent discharging oil or other chemicals and safeguard the environment. Always disconnect
power before servicing pump. Always use fuse size specified in specifications. These bilge pumps are
designed to evacuate standing bilge water only. These pumps may not prevent boat sinkage due to storms,
rough weather, unsafe boating, improper installation procedures or hull damage.
measures to prevent discharging oil or other chemicals and safeguard the environment. Always disconnect
power before servicing pump. Always use fuse size specified in specifications. These bilge pumps are
designed to evacuate standing bilge water only. These pumps may not prevent boat sinkage due to storms,
rough weather, unsafe boating, improper installation procedures or hull damage.
WARNING
Favor de referirse a www.shurflo.com para instrucciones de la instalación del producto y su operación, disponible en varios idiomas.
Fare riferimento al sito www.shurflo.com per manuali multilingue di installazione ed utilizzo prodotti.
Mehrsprachige Hinweise zu Installation und Betrieb des Produktes finden Sie unter www.shurflo.com
Please refer to www.shurflo.com for multi-lingual product installation and operating instructions'
V
euillez vous réferer au site www.shurflo.com pour l'installation produit multilingue ainsi que pour le mode d'emploi.
911-758 Rev D
© 2008 SHURflo, LLC All Rights Reserved
© 2008 SHURflo, LLC All Rights Reserved
Patent #: 6715994
Page 2 of 2
SHURflo reserves the right to update
specifications, prices, or make substitutions.
SHURflo, LLC Headquarters
5900 Katella Avenue
Cypress, California 90630
Phone (562) 795-5200
5900 Katella Avenue
Cypress, California 90630
Phone (562) 795-5200
Ÿ Toll Free (800) 854-3218
Fax (562) 795-7564
SHURflo Europe, Middle East, Africa
Pentair Water Belgium bvba,
Industriepark Wolfstee, Toekomstlaan 30
B-2200 Herentals, Belgium
Phone +32-14-283500
Pentair Water Belgium bvba,
Industriepark Wolfstee, Toekomstlaan 30
B-2200 Herentals, Belgium
Phone +32-14-283500
Ÿ Fax +32-14-283505
SHURflo, LLC East
52748 Park Six Court
Elkhart, Indiana 46514-5427
Phone (562) 795-5200
52748 Park Six Court
Elkhart, Indiana 46514-5427
Phone (562) 795-5200
Ÿ Toll Free (800) 854-3218
Fax (574) 264-2169