Recom Lighting Indoor panel mounted lamp YSX140 White YSX140 Fiche De Données
Codes de produits
YSX140
Technical Data
The LED downlight can be operated only with a constant current source. Never use
a commercial halogen transformer or a conventional power supply unit!
Order No. .............................. 577450
577453
577454
Constant current ................... 750 mA
1,000 mA
1,500 mA
Power input ........................... Max. 20 W
Max. 25 W
Max. 39 W
Luminous fl ux ....................... 1450 lm
1900 lm
2540 lm
Colour temperature ............... 3,000 K
3,000 K
3,000 K
Angle of radiation .................. 60°
60°
60°
Outside diameter .................. 140 mm
160 mm
200 mm
Height ................................... 81 mm
81 mm
80 mm
Installation depth min. ........... 120 mm
120 mm
120 mm
Mounting hole, diameter ....... 125 mm
141 mm
181 mm
Weight .................................. 660 g
775 g
1240 g
Protection class .................... III
Installation location ............... Only in dry, enclosed indoor spaces
Installation location ............... Only in dry, enclosed indoor spaces
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1,
D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfi lming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
technology and equipment reserved.
© Copyright 2012 by Conrad Electronic SE.
☞
Our tip:
When installing the LED downlight in a ceiling panel, check the correct hole diameter
on an offcut in order to be sure of the size. Nothing is more frustrating than drilling a
hole bigger than the one needed in an expensive and high-quality ceiling panel.
on an offcut in order to be sure of the size. Nothing is more frustrating than drilling a
hole bigger than the one needed in an expensive and high-quality ceiling panel.
Drill the hole from the visible side, so the edges of the hole do not break away.
When using a hole saw drill, a 3 mm hole can be pre-drilled so that the centre drill of
the hole saw does not slip out of place.
the hole saw does not slip out of place.
• For instance, put the ceiling panel in place and guide the power line through the borehole.
• Connect the two power cables of the LED downlight to the mains supply. The red cable must
• Connect the two power cables of the LED downlight to the mains supply. The red cable must
be connected to the positive pole (+), the black cable to the negative pole (-). Use suitable
connection blocks or plugs to avoid short circuits.
connection blocks or plugs to avoid short circuits.
Warning!
The LED downlight can be operated only with a constant current source (also called
LED ballast or LED driver). Never use a commercially available halogen transformer
or power supply unit, this will destroy the LED downlight, loss of guarantee!
LED ballast or LED driver). Never use a commercially available halogen transformer
or power supply unit, this will destroy the LED downlight, loss of guarantee!
In case of doubt, consult a specialist.
Refer to chapter “Technical Data” for information on required current and power
consumption of the LED downlight.
consumption of the LED downlight.
• Insert the LED downlight in the prepared installation hole.
To this end, bend the retaining bracket backwards and plug it, for example through the hole
To this end, bend the retaining bracket backwards and plug it, for example through the hole
in the ceiling panel.
Slide in the LED light until it is well-fi tted in the hole; in the process, the tilt the brackets
downwards and fi x the LED light in the installation hole.
Make sure the connection cables are not squeezed.
• Turn on the power supply to the LED driver (constant power supply) and check whether the
• Turn on the power supply to the LED driver (constant power supply) and check whether the
LED downlight is functioning properly.
If the recessed LED downlight does not light up, turn off the power immediately.
Check whether the polarity of the recessed LED downlight’s cable is correct (red
cable = plus/+; black cable = minus/-) and make sure that the LED driver is working
correctly.
cable = plus/+; black cable = minus/-) and make sure that the LED driver is working
correctly.
Maintenance and Care
• The LED downlight is maintenance-free. The LED used is very long-lasting and it cannot be
replaced.
• Prior to cleaning (e.g. to remove dust from the light-emitting opening), the LED downlight
should be turned off or the power supply disconnected. Furthermore, allow the LED downlight
to cool down suffi ciently.
to cool down suffi ciently.
• The exterior of the LED downlight should be wiped only with a clean, soft, dry cloth. Do not
use aggressive cleaning agents or chemical solutions that could damage the housing (discol-
ouring) or impair operation.
ouring) or impair operation.
Do not press too hard on the housing or the transparent cover, as scratches might occur.
Dust can easily be removed using a clean, soft brush and a vacuum cleaner.
Dust can easily be removed using a clean, soft brush and a vacuum cleaner.
Disposal
Dispose of the unserviceable product according to the relevant statutory regulations!