Esotec Solar garden light LED Cold white Stainless steel 102602 Fascicule

These instructions relate ONLY to this product and contain important infor-

mation for using the product for the first time. Please keep these instructions 

for later reference and should always accompany the product in the event of 

transference to a new user.

Dear Costumer, 

Thank you for purchasing the solar light. 

With this solar light you purchased a product manufactured according to the 

current state of technology. 

To maintain this state and guarantee a safe operation, you as the user will have 

to follow this operating manual!

  

Due to safety and admission reasons (CE) it is not allowed to arbitrarily recon-

struct and/or change the solar light. 

Therefore, please keep to the operating manual. 

The accident prevention rules of the association of the industrial trade coope-

rative association for electric plants and working material are to be considered 

in industrial environments

The solar light is constructed for the outdoor usage and operation. The 

integrated accumulator is charged by the solar cell in the upper part of the 

light.  At darkness, the light is automatically switched on and is switched 

out at sunrise. As light source, 1 very strong light emitting diode (LED) are 

installed. These LED guarantee a strong luminosity with only low power 

consumption. 

In case of longer periods without sunshine (insolation) the accumulator is 

charged only insufficiently and is thus not able to guarantee a permanent 

readiness for operation. However, this does not indicate that the solar light 

is defect. Please wait for the next sunny days and the light will again be 

working accordingly

1.  Please carefully take all parts out of the package. 

2.  Take out the plastic part (1) in the end of the metal tube. 

Take the two platic parts apart (2) and press the ground 

stik into the plastig part. Press the plastic part with 

ground stik into the tube (3). 

3.  Hold the upper part and screw off the lower part of the 

lamp head and take apart (4+5) the parts. Adjust the 

switch to the position “ON” (6) take the two parts together 

again, take both stainless steel tube and light head to-

gether.

4.  Please carefully connect the earth rod with the bar and 

insert it into the ground. 

Note: Please do not use force. 

Note: The duration of illumination is strongly dependent on 

the intensity and duration of sunshine during the day. During 

the winter months the duration of illumination will generally 

be shorter. If the lamp should not irradiate on the first eve-

ning, please wait for a sunny day.

1.  Hold the upper part and screw off the lower part (1) of the lamp head and take 

apart (2) the parts.  

2.  Take the used accumulator out of the battery compartment (3) and insert a new 

accumulators according to polarity, into the battery compartment. It is recommen-

ded to charge the new accumulator in a battery charger before inserting them. 

3.  Re-assemble the lamp in reverse order. 

Note: Used batteries or accumulators must be disposed of in a non-polluting way and 

do not belong into the domestic waste. Your dealer is legally obliged to take back and 

recycle old accumulators. 

• 

An outside light source (e.g. streetlight) simulates daylight and prevents the 

lamp from switching on. Place the lamp at a darker location. 

• 

Is the lamp connected?

• 

Accumulator weak or defective. Exchange of the accumulators.

•  Solar module:  

270 mWp cristalline

•  LED: 

Nichia LED

•  Light angle:  

120°

•  Light color:  

item-no: 102602: 6500 K, item-no: 102603: 2800 K

•  Light intensity: 

item-no: 102602: 12 lm, item-no: 102603: 10 lm

•  Degree of protection:   IP 44 

•  Protection class:  

III

•  Battery: 

1x NiMh 1.2 V/900 mAh (Micro AAA)

•  Luminosity period: 

Max. 8 hrs with full battery

•  Working temperature:   -20°C bis + 40°C

esotec GmbH  -  Weberschlag 9 -  D-92729 Weiherhammer

Tel.-Nr: +49 9605-92206-0 

Fax.-Nr: +49 9605-92206-10

e-mail:info@esotec.de  

Internet: www.esotec.de

-  Rechargeable batteries should not be played with by children. Never leave rechar-

geable batteries lying around; they could be swallowed by children or pets. 

-  Rechargeable batteries must never be short-circuited, disassembled or thrown into 

fire. This leads to a danger of explosion!

-  Leaking or damaged rechargeable batteries can cause chemical burns when they 

come into contact with skin. For this reason, please make use of suitable protective 

gloves. 

-  Rechargeable batteries should only be replaced by structurally identical rechar-

geable batteries from the same manufacturer. Normal batteries must not be used 

since these are not rechargeable.

-  Make sure the rechargeable batteries are inserted with the correct polarity.

-  For long periods of time of non-use (for example, storage), remove the inserted 

rechargeable batteries to avoid damages via the leaking rechargeable batteries. 

Dear customer,

please cooperate in avoiding waste. When you intend to dispose of the 

product in future, please consider that it contains valuable raw materials 

suited for recycling.

Therefore, do not dispose it of with domestic waste but bring it to a collec-

tion point for the recycling of waste electrical and electronic equipment. 

Thank you very much for your cooperat

       

!

• 

Used batteries or accumulators must be disposed in the 

domestic waste. 

• 

The consumer is legally obliged to bring back old accumu-

lators upon usage, e.g. to public waste collecting locations 

or to the place (shops, etc.) where those batteries are sold.

•

Batteries that contain harmful substances are marked 

with the “strike through dustbin”  and one of the chemical 

symbols. 

1.

2.

3.