Insys GPRS 5.0 Ethernet 11-02-01-03-10.018 Manuel D’Utilisation
Codes de produits
11-02-01-03-10.018
INSYS GPRS 5.0 Ethernet
International Safety Instructions
Dez-06
59
IMPORTANT!
Cellular terminals or mobiles operate using radio signals and cellular networks. Because of
this, connection cannot be guaranteed at all times under all conditions. Therefore, you
should never rely solely upon any wireless device for essential communications, for example
emergency calls.
this, connection cannot be guaranteed at all times under all conditions. Therefore, you
should never rely solely upon any wireless device for essential communications, for example
emergency calls.
Remember, in order to make or receive calls, the cellular terminal or mobile must be
switched on and in a service area with adequate cellular signal strength.
switched on and in a service area with adequate cellular signal strength.
Some networks do not allow for emergency calls if certain network services or phone
features are in use (e.g. lock functions, fixed dialing etc.). You may need to deactivate those
features before you can make an emergency call. Some networks require that a valid SIM
card be properly inserted in the cellular terminal or mobile.
features are in use (e.g. lock functions, fixed dialing etc.). You may need to deactivate those
features before you can make an emergency call. Some networks require that a valid SIM
card be properly inserted in the cellular terminal or mobile.
9.2
Compliance with FCC Rules and Regulations
The FCC Equipment Authorization Certification for the TC63 reference application is listed
under the
under the
FCC identifier QIPTC63
IC: 267W-TC63
granted to Siemens AG.
IC: 267W-TC63
granted to Siemens AG.
The TC63 reference application registered under the above identifier is certified to be in
accordance with the following Rules and Regulations of the Federal Communications
Commission (FCC).
accordance with the following Rules and Regulations of the Federal Communications
Commission (FCC).
Power listed is ERP for Part 22 and EIRP for Part 24
“This device contains GSM and GPRS Class12 functions in the 900 and
1800MHz Band which are not operational in U.S. Territories.
This device is to be used only for mobile and fixed applications. The antenna(s)
used for this transmitter must be installed to provide a separation distance of
at least 20cm from all persons and must not be co-located or operating in
conjunction with any other antenna or transmitter. Users and installers must
be provided with antenna installation instructions and transmitter operating
conditions for satisfying RF exposure compliance. Antennas used for this OEM
module must not exceed 8.4dBi gain (GSM 1900) and 2.9dBi (GSM 850) for
mobile and fixed operating configurations. This device is approved as a
module to be installed in other devices.”
1800MHz Band which are not operational in U.S. Territories.
This device is to be used only for mobile and fixed applications. The antenna(s)
used for this transmitter must be installed to provide a separation distance of
at least 20cm from all persons and must not be co-located or operating in
conjunction with any other antenna or transmitter. Users and installers must
be provided with antenna installation instructions and transmitter operating
conditions for satisfying RF exposure compliance. Antennas used for this OEM
module must not exceed 8.4dBi gain (GSM 1900) and 2.9dBi (GSM 850) for
mobile and fixed operating configurations. This device is approved as a
module to be installed in other devices.”
Manufacturers of mobile or fixed devices incorporating TC63 modules are advised to
include instructions according to above mentioned RF exposure statements in their end
product user manual.
Please note that changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
If the final product is not approved for use in U.S. territories the application manufacturer
shall take care that the 850 MHz and 1900 MHz frequency bands be deactivated and that
band settings be inaccessible to end users. If these demands are not met (e.g. if the AT
interface is accessible to end users), it is the responsibility of the application manufacturer
to always ensure that the application be FCC approved regardless of the country it is
marketed in. The frequency bands can be set using the command
AT^SCFG
include instructions according to above mentioned RF exposure statements in their end
product user manual.
Please note that changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
If the final product is not approved for use in U.S. territories the application manufacturer
shall take care that the 850 MHz and 1900 MHz frequency bands be deactivated and that
band settings be inaccessible to end users. If these demands are not met (e.g. if the AT
interface is accessible to end users), it is the responsibility of the application manufacturer
to always ensure that the application be FCC approved regardless of the country it is
marketed in. The frequency bands can be set using the command
AT^SCFG
="Radio/Band"[,<rbp>][, <rba>].
The FCC label of the module must be visible from the outside. If not, the host device is
required to bear a second label stating, “Contains FCC ID QIPTC63”.
required to bear a second label stating, “Contains FCC ID QIPTC63”.