Texas Instruments Delfino C28346 DIM168 ControlCARD TMDSCNCD28346-168 TMDSCNCD28346-168 Fiche De Données
Codes de produits
TMDSCNCD28346-168
SPRS516D – MARCH 2009 – REVISED AUGUST 2012
6.15.8 External Interface Ready-on-Write Timing With One External Wait State
Table 6-44. External Interface Write Switching Characteristics (Ready-on-Write, 1 Wait State)
PARAMETER
MIN
MAX
UNIT
t
d(XCOH-XZCSL)
Delay time, XCLKOUT high to zone chip-select active low
0
2
ns
t
d(XCOHL-XZCSH)
Delay time, XCLKOUT high or low to zone chip-select inactive high
–0.2
0.9
ns
t
d(XCOH-XA)
Delay time, XCLKOUT high to address valid
1.5
ns
t
d(XCOHL-XWEL)
Delay time, XCLKOUT high/low to XWE0, XWE1 low
(1)
–0.3
0.7
ns
t
d(XCOHL-XWEH)
Delay time, XCLKOUT high/low to XWE0, XWE1 high
(1)
–0.5
0.5
ns
t
d(XCOH-XRNWL)
Delay time, XCLKOUT high to XR/W low
–0.2
1.5
ns
t
d(XCOHL-XRNWH)
Delay time, XCLKOUT high/low to XR/W high
0.3
0.6
ns
t
en(XD)XWEL
Enable time, data bus driven from XWE0, XWE1 low
–7.5
ns
t
d(XWEL-XD)
Delay time, data valid after XWE0, XWE1 active low
0
4
ns
t
h(XA)XZCSH
Hold time, address valid after zone chip-select inactive high
(2)
ns
t
h(XD)XWE
Hold time, write data valid after XWE0, XWE1 inactive high
(1)
TW – 7.5
(3)
ns
t
dis(XD)XRNW
Maximum time for processor to release the data bus after XR/W
0
ns
inactive high
(1)
XWE1 is used in 32-bit data bus mode only. In 16-bit, this signal is XA0.
(2)
During inactive cycles, the XINTF address bus always holds the last address put out on the bus. This includes alignment cycles.
(3)
TW = trail period, write access (see
)
Table 6-45. Synchronous XREADY Timing Requirements (Ready-on-Write, 1 Wait State)
(1)
MIN
MAX
UNIT
t
su(XRDYsynchL)XCOHL
Setup time, XREADY (synchronous) low before XCLKOUT high/low
8
ns
t
h(XRDYsynchL)
Hold time, XREADY (synchronous) low
1t
c(XTIM)
ns
t
su(XRDYsynchH)XCOHL
Setup time, XREADY (synchronous) high before XCLKOUT high/low
8
ns
t
h(XRDYsynchH)XZCSH
Hold time, XREADY (synchronous) held high after zone chip select high
0
ns
(1)
The first XREADY (synchronous) sample occurs with respect to E in
E =(XWRLEAD + XWRACTIVE) t
c(XTIM)
When first sampled, if XREADY (synchronous) is high, then the access will complete. If XREADY (synchronous) is low, it is sampled
again each t
again each t
c(XTIM)
until it is high.
For each sample, setup time from the beginning of the access can be calculated as:
F = (XWRLEAD + XWRACTIVE +n –1) t
F = (XWRLEAD + XWRACTIVE +n –1) t
c(XTIM)
– t
su(XRDYsynchL)XCOHL
where n is the sample number: n = 1, 2, 3, and so forth.
Table 6-46. Asynchronous XREADY Timing Requirements (Ready-on-Write, 1 Wait State)
(1)
MIN
MAX
UNIT
t
su(XRDYasynchL)XCOHL
Setup time, XREADY (asynchronous) low before XCLKOUT high/low
8
ns
t
h(XRDYasynchL)
Hold time, XREADY (asynchronous) low
1t
c(XTIM)
ns
t
su(XRDYasynchH)XCOHL
Setup time, XREADY (asynchronous) high before XCLKOUT high/low
8
ns
t
h(XRDYasynchH)XZCSH
Hold time, XREADY (asynchronous) held high after zone chip select high
0
ns
(1)
The first XREADY (synchronous) sample occurs with respect to E in
E = (XWRLEAD + XWRACTIVE –2) t
c(XTIM)
. When first sampled, if XREADY (asynchronous) is high, then the access will complete. If
XREADY (asynchronous) is low, it is sampled again each t
c(XTIM)
until it is high.
For each sample, setup time from the beginning of the access can be calculated as:
F = (XWRLEAD + XWRACTIVE –3 + n) t
F = (XWRLEAD + XWRACTIVE –3 + n) t
c(XTIM)
– t
su(XRDYasynchL)XCOHL
where n is the sample number: n = 1, 2, 3, and so forth.
152
Electrical Specifications
Copyright © 2009–2012, Texas Instruments Incorporated
Product Folder Link(s):