Atmel Xplained Pro Evaluation Kit for the ATSAMD21J18A Microcontroller ATSAMD21-XPRO ATSAMD21-XPRO Fiche De Données
Codes de produits
ATSAMD21-XPRO
140
Atmel | SMART SAM D21 [DATASHEET]
Atmel-42181C–SAM-D21_Datasheet–07/2014
16.4 Signal Description
The I/O lines are automatically selected when XOSC or XOSC32K are enabled. Refer to CRs_PINOUT_OSC.
16.5 Product Dependencies
In order to use this peripheral, other parts of the system must be configured correctly, as described below.
16.5.1 I/O Lines
I/O lines are configured by SYSCTRL when either XOSC or XOSC32K are enabled, and need no user configuration.
16.5.2 Power Management
The SYSCTRL can continue to operate in any sleep mode where the selected source clock is running. The SYSCTRL
interrupts can be used to wake up the device from sleep modes. The events can trigger other operations in the system
without exiting sleep modes. Refer to
interrupts can be used to wake up the device from sleep modes. The events can trigger other operations in the system
without exiting sleep modes. Refer to
16.5.3 Clocks
The SYSCTRL gathers controls for all device oscillators and provides clock sources to the Generic Clock Controller
(GCLK). The available clock sources are: XOSC, XOSC32K, OSC32K, OSCULP32K, OSC8M, DFLL48M and
FDPLL96M.
(GCLK). The available clock sources are: XOSC, XOSC32K, OSC32K, OSCULP32K, OSC8M, DFLL48M and
FDPLL96M.
The SYSCTRL bus clock (CLK_SYSCTRL_APB) can be enabled and disabled in the Power Manager, and the default
state of CLK_SYSCTRL_APB can be found in the Peripheral Clock Masking section in the
state of CLK_SYSCTRL_APB can be found in the Peripheral Clock Masking section in the
The clock used by BOD33in sampled mode is asynchronous to the user interface clock (CLK_SYSCTRL_APB).
Likewise, the DFLL48M control logic uses the DFLL oscillator output, which is also asynchronous to the user interface
clock (CLK_SYSCTRL_APB). Due to this asynchronicity, writes to certain registers will require synchronization between
the clock domains. Refer to
Likewise, the DFLL48M control logic uses the DFLL oscillator output, which is also asynchronous to the user interface
clock (CLK_SYSCTRL_APB). Due to this asynchronicity, writes to certain registers will require synchronization between
the clock domains. Refer to
for further details.
16.5.4 Interrupts
The interrupt request line is connected to the Interrupt Controller. Using the SYSCTRL interrupts requires the Interrupt
Controller to be configured first. Refer to
Controller to be configured first. Refer to
for details.
16.5.5 Debug Operation
When the CPU is halted in debug mode, the SYSCTRL continues normal operation. If the SYSCTRL is configured in a
way that requires it to be periodically serviced by the CPU through interrupts or similar, improper operation or data loss
may result during debugging.
way that requires it to be periodically serviced by the CPU through interrupts or similar, improper operation or data loss
may result during debugging.
If a debugger connection is detected by the system, BOD33 reset will be blocked.
Signal Name
Types
Description
XIN
Analog Input
Multipurpose Crystal Oscillator or external
clock generator input
clock generator input
XOUT
Analog Output
External Multipurpose Crystal Oscillator
output
output
XIN32
Analog Input
32kHz Crystal Oscillator or external clock
generator input
generator input
XOUT32
Analog Output
32kHz Crystal Oscillator output