MEAN WELL LED driverLED-switching power supply PCD-25-700B PCD-25-700B Fiche De Données
Codes de produits
PCD-25-700B
SPECIFICATION
MODEL
PCD-25-1400
PCD-25-1050
PCD-25-700
PCD-25-350
RATED CURRENT
OPERATING VOLTAGE RANGE
RATED POWER
OUTPUT
SETUP TIME
FREQUENCY RANGE
POWER FACTOR (Typ.)
EFFICIENCY (Typ.)
AC CURRENT (Typ.)
INPUT
INRUSH CURRENT(max.)
LEAKAGE CURRENT
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSION
OTHERS
NOTE
PACKING
SHORT CIRCUIT
OVER TEMPERATURE
1400mA
1050mA
700mA
350mA
25.2W
25.2W
25.2W
20.3W
2Vp-p
2.2Vp-p
2.7Vp-p
4.6Vp-p
63V
50V
35V
25V
500ms / 230VAC 2000ms / 115VAC at full load
47 ~ 63Hz
PF>0.9/115VAC, PF>0.9/230VAC, PF>0.9/277VAC at full load (Please refer to "Power Factor Characteristic" curve)
80%
80.5%
81%
82%
0.6A/115VAC
0.3A/230VAC
0.2A/277VAC
<0.5mA 120VAC / 240VAC
Hiccup mode, recovers automatically after fault condition is removed.
-30 ~ +60
℃ (Refer to "Derating Curve")
20 ~ 95% RH non-condensing
-40 ~ +80
, 10 ~ 95% RH
℃
±
℃
℃
0.03%/
(0 ~ 50
)
10 ~ 500Hz, 2G 12min./1cycle, period for 72min. each along X, Y, Z axes
906.5
℃
K hrs min. MIL-HDBK-217F (25
)
84*57*29.5mm (L*W*H)
0.19Kg; 72pcs/14.7Kg/0.92CUFT
25W Single Output AC Dimmable LED Power Supply
■
Features :
P C D - 2 5
s e r i e s
RIPPLE & NOISE (max.)
Note.1
ENVIRONMENT
SAFETY &
EMC
PROTECTION
Shut down o/p voltage
, re-power on to recover
SAFETY STANDARDS
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
I/P-O/P:3.75KVAC
I/P-O/P:100M Ohms / 500VDC / 25℃/ 70% RH
24 ~ 36V
40 ~ 58V
12 ~ 18V
16 ~ 24V
PCD-25-350 A
A : With AC input 90~ 135VAC.
B : With AC input 180~ 295VAC.
B : With AC input 180~ 295VAC.
File Name:PCD-25-SPEC 2014-01-09
1. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
2. Direct connecting to LEDs is suggested, but is not suitable for using additional drivers.
3. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED power supply can only be used behind a switch without permanently
connected to the mains.
UL8750, CSA C22.2 No. 250.0-08(except for PCD-25-350, PCD-25-700), ENEC EN613471, EN61347-2-13, EN62384(for B type only),
IP30 approved ; design refer to UL60950-1, TUV EN60950-1, EN61347-1, EN61347-2-13
IP30 approved ; design refer to UL60950-1, TUV EN60950-1, EN61347-1, EN61347-2-13
‧
AC phase-cut dimming
‧
Work with leading edge and trailing edge TRIAC dimmers
‧
115VAC or 230VAC models available
‧
Built-in active PFC function
‧
Constant current design
‧
Protections: Short circuit / Over temperature
‧
Cooling by free air convection
‧
Fully isolated plastic case
‧
IP30 design
‧
Ⅱ
‧
Class 2 power unit
‧
‧
100% full load burn-in test
‧
‧
High reliability
‧
3 years warranty
Class power unit, no FG
Suitable for indoor LED lighting applications
Low cost
NO LOAD OUTPUT
(max.)
VOLTAGE
±5.0%
Compliance to
(B type only),
EN55015
EN61000-3-2 Class C ; EN61000-3-3, FCC part 18 non-consumer equipment (A type only)
Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024,EN61547, light industry level, criteria A
EMC IMMUNITY
EMC EMISSION
CURRENT ACCURACY
COLD START 10A(t
width
=20 s measured at 50% I
peak
) at 115VAC / 230VAC
μ
SELV
( for B type only)
( for A type only)
( for B type only)
( for B type only)
( for PCD-25-350/700 )
( except PCD-25-350/700 )
F
110
IP30