MEAN WELL LED driverLED-switching power supply HLG-320H-24B HLG-320H-24B Fiche De Données

I/P-O/P:3.75KVAC     I/P-FG:2KVAC     O/P-FG:1.5KVAC

I/P-O/P, I/P-FG, O /P-FG:100M Ohms / 500VDC / 25

/ 70% RH

℃

HLG-320H-12 A

A : IP65 rated. Output voltage and constant current level can be adjusted through internal potentiometer.
B : IP67 rated. Constant current level adjustable through output cable with 1~10Vdc or PWM signal or resistance.
C : Terminal block for I/O connection. Output voltage and constant current level can be adjusted through internal 

D (option) : IP67 rated. Timer dimming function, contact MEAN WELL for details.

potentiometer.

Can be adjusted by internal potentiometer A type and C type only

2500ms,80ms/115VAC      500ms,80ms/230VAC at full load 

15ms at full load     230VAC /115VAC

90 ~ 305VAC          127 ~ 431VDC

47 ~ 63Hz

PF>0.98/115VAC, PF>0.95/230VAC, PF>0.94/277VAC at full load (Please refer to "Power Factor Characteristic" curve)

3.5A / 115VAC          1.65A / 230VAC          1.45A / 277VAC

<0.75mA / 277VAC

95 ~ 108%

Protection type : Constant current limiting, recovers automatically after fault condition is removed

Compliance to EN55015, EN55022 (CISPR22) Class B, EN61000-3-2  Class C (

50% load) ; EN61000-3-3

≧

Compliance to EN61000-4-2,3,4,5,6,8,11, EN61547, EN55024, light industry level (surge 4KV),  criteria B

-40 ~ +70

 (Refer to "Derating Curve")

℃

20 ~ 95% RH non-condensing

-40 ~ +80

, 10 ~ 95% RH

℃

±

℃

℃

0.03%/

 (0 ~ 50

)

10 ~ 500Hz, 5G 12min./1cycle, period for  72min. each along X, Y, Z axes

J61347-2-13

 approved

 

 

(except for HLG-320H C type)

UL8750, 

EN61347-1, EN61347-2-13 independent

(except for HLG-320H C type)

CSA C22.2 No. 250.0-08, 

 

,

 J61347-1,

 IP65 or IP67

,

157.1K hrs min.      MIL-HDBK-217F (25

)

℃

252*90*43.8mm (L*W*H)

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25  of ambient temperature.

℃

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance : includes set up tolerance, line regulation and load regulation.

4. Please refer to "DRIVING METHODS OF LED MODULE".

5. Derating may be needed under low input voltages. Please check the 

 for more details.

static characteristics

6. A type and C type only.

7. Safety and EMC design refer to EN60598-1, subject CNS15233, GB7000.1, FCC part18.

8. Length of set up time is measured at cold first start. Turning ON/OFF the power supply may lead to increase of the set up time.

9. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the 

    complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.

10. Refer to warranty statement.

11. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED power supply can only be used behind a switch without permanently 

      connected to the mains.

1.88Kg; 8pcs/16Kg/0.92CUFT

Protection type : Shut down and latch off o/p voltage, re-power on to recover

Shut down and latch off o/p voltage, re-power on to recover

320W Single Output Switching Power Supply

‧

Universal AC input / Full range (up to 305VAC)

‧

Built-in active PFC function

‧

High efficiency up to 95%

‧

Protections: Short circuit / Over current / Over voltage / Over temperature 

‧

Cooling by free air convection

‧

OCP point adjustable through output cable or internal potentiometer

‧

IP67 / IP65 design for indoor or outdoor installations

‧

Type HL LED Driver for use in Class  , Division 2 hazardous location luminaires

Ⅰ

‧

Three in one dimming function (1~10Vdc or PWM signal or resistance)

‧

Suitable for LED lighting and street lighting applications

‧

Compliance to worldwide safety regulations for lighting 

‧

Suitable for dry / damp / wet location 

‧

5 years warranty (Note.10)

■

 Features :

IP65 IP67

Hiccup mode, recovers automatica lly after fault condition is removed.

Blank : IP67 rated. Cable for I/O connection. 

14 ~ 17V

17.5 ~ 21V

22.5 ~ 27V

27 ~ 33V

33 ~ 37V

40 ~ 46V

53.5 ~ 60V

46.5 ~ 53V

59 ~ 65V

91%

91.5%

92.5%

93%

93.5%

94%

94%

94.5%

94%

94.5%

94.5%

95%

95%

95%

95%

95%

95%

95%

±3.0%

11 ~ 22A

±2.0%

9.5 ~ 19A

±1.5%

7.5 ~ 15A

±1.0%

6.67 ~ 13.34A

±1.0%

5.35 ~ 10.7A

±1.0%

4.45 ~ 8.9A

±1.0%

3.35 ~ 6.7A

±0.5%

±0.5%

±0.5%

±0.5%

±0.5%

±0.5%

±0.5%

±2.0%

±1.5%

±1.0%

±0.5%

±0.5%

±0.5%

±0.5%

±1.0%

2.97 ~ 5.95A

±0.5%
±0.5%

±1.0%

3.8 ~ 7.65A

±0.5%
±0.5%

12V

6 ~12V

15V

7.5 ~ 15V

20V

10 ~ 20V

24V

12 ~ 24V

30V

15 ~ 30V

36V

18 ~ 36V

48V

24 ~ 48V

22A

19A

15A

13.34A

10.7A

8.9A

6.7A

264W

285W

300W

320.16W

321W

320.4W

321.6W

150mVp-p

150mVp-p

13.5 ~ 17V

150mVp-p

17 ~ 22V

150mVp-p

21 ~ 26V

200mVp-p

26 ~ 32V

250mVp-p

32 ~ 39V

250mVp-p

43 ~ 52V

10.8 ~ 13.5V

54V

27 ~ 54V

5.95A

321.3W

350mVp-p

49 ~ 58V

42V

21 ~ 42V

7.65A

321.3W

250mVp-p

38 ~ 45V

COLD START 70A(t

=1010  s measured at 50% I

) at 230VAC 

width

peak

μ

THD< 20% when output loading

50% at 115VAC/230VAC input and output loading

75% at 277VAC input

≧

≧