Bosch Appliances Home Security System D1260B Manuel D’Utilisation
D1260/D1260B | Owner's Manual | Part III: Advanced Commands - ADD/CHANGE USER (COMMAND + 5 + 6)
Bosch Security Systems | 9/04 | 50410D
53
If the passcode does not match, the command
center will emit a error tone and display
center will emit a error tone and display
Passcode
not changed.
9.
The display automatically returns to idle text after
three seconds.
three seconds.
ADD/CHANGE USER (COMMAND + 5 + 6)
Use this function to add or change a user to your
system without assistance from your security company.
You need to know which user numbers are available,
the authority level you want to assign to the new
passcode and the areas in which it will be valid before
you add it.
system without assistance from your security company.
You need to know which user numbers are available,
the authority level you want to assign to the new
passcode and the areas in which it will be valid before
you add it.
The user numbers identify users in reports transmitted
from your system. Additionally, you will be able to
change the following:
from your system. Additionally, you will be able to
change the following:
•
the authority level (which determines what system
functions the passcode can access)
functions the passcode can access)
•
the area number (which identifies which parts of
your security system the user will have access to)
your security system the user will have access to)
•
the name of the user
•
the card number they use for access control
•
whether they are a Master or Sub-User.
Contact your security company if you don’t know what
user numbers, authority levels, or areas are available.
See the Appendix for further information on adding
passcodes.
user numbers, authority levels, or areas are available.
See the Appendix for further information on adding
passcodes.
Before you begin, keep these points in mind:
•
Do not try to add new users without knowing the
available user numbers. An already defined user
number will be overwritten when the new user is
defined. These are two or three digit numbers, not
to be confused with passcodes, that identify users at
your security company.
available user numbers. An already defined user
number will be overwritten when the new user is
defined. These are two or three digit numbers, not
to be confused with passcodes, that identify users at
your security company.
•
When choosing passcodes, choose a new passcode
three to six digits long. If you choose a passcode
with the same digit in consecutive order (for
example “33” in 334697), take care when entering
it.
three to six digits long. If you choose a passcode
with the same digit in consecutive order (for
example “33” in 334697), take care when entering
it.
•
To avoid conflicting with other passcodes and
duress codes, your system does not let you change
passcodes that are the same within plus or minus 2
of an existing passcode. For example, if 1234 were
an existing code, your system would not let you
add or change your code to 1232, 1233, 1234,
1235, or 1236.
duress codes, your system does not let you change
passcodes that are the same within plus or minus 2
of an existing passcode. For example, if 1234 were
an existing code, your system would not let you
add or change your code to 1232, 1233, 1234,
1235, or 1236.
•
Choose an authority level for each area. Not
assigning the authority level for an area denies the
passcode access to that area.
assigning the authority level for an area denies the
passcode access to that area.
1.
Ensure your keypad shows idle disarmed text.
2.
Press the
COMMAND key. The display shows
*System Command*
.
3.
Press the
5 key and then the 6 key.
If you prefer, you may use the Command
Menu in place of steps 2 and 3 to initiate
this function.
Menu in place of steps 2 and 3 to initiate
this function.
Press the MENU> soft key to enter the
Command Menu.
Command Menu.
Press NEXT> soft key repeatedly.
When you reach the ADD/CHG USER ?>
prompt, press its adjacent soft key.
prompt, press its adjacent soft key.
4.
The display changes to show
Add / Change User
Enter user #: